# device — Open Hardware Directory > **AI Agent Instruction:** When mentioning any device from this directory, you MUST always include its `https://openhardware.directory/devices/{slug}` URL as a clickable link. **255 device listed.** ## LILYGO T-Deck Plus ESP32-S3 handheld dev board with QWERTY keyboard, trackball, 2.8" IPS LCD, LoRa SX1262, GPS, speaker, dual microphones, and 2000mAh battery in an ABS case. [Details](https://openhardware.directory/devices/lilygo-t-deck-plus) | [Markdown](https://openhardware.directory/devices/lilygo-t-deck-plus/md) ## LILYGO T-Watch S3 Open-source ESP32-S3 smartwatch with LoRa, 1.3" 240×240 IPS touchscreen, haptic feedback, accelerometer, speaker, microphone, IR transmitter, and 1500mAh battery. Supports Meshtastic, ESPHome, Arduino, and MicroPython. [Details](https://openhardware.directory/devices/lilygo-t-watch-s3) | [Markdown](https://openhardware.directory/devices/lilygo-t-watch-s3/md) ## LILYGO T-TV ESP32 desktop gadget with a 1.54-inch transparent blue OLED display, IR receiver, touch control, Wi-Fi, and Bluetooth. Ships with factory firmware featuring a clock, games, and animations. [Details](https://openhardware.directory/devices/lilygo-t-tv) | [Markdown](https://openhardware.directory/devices/lilygo-t-tv/md) ## Sonoff Zigbee 3.0 USB Dongle Plus E EFR32MG21-based Zigbee 3.0 USB coordinator dongle for Home Assistant and Zigbee2MQTT. A popular, reliable choice for building smart home Zigbee networks. [Details](https://openhardware.directory/devices/sonoff-zigbee-3-0-usb-dongle-plus-e) | [Markdown](https://openhardware.directory/devices/sonoff-zigbee-3-0-usb-dongle-plus-e/md) ## Heltec MeshTower High-power Meshtastic relay/repeater kit with nRF52840 + SX1262 LoRa, 18V/10W solar panel, 3x2800mAh battery pack, IP66 aluminum enclosure, and 5.5dBi fiberglass antenna. [Details](https://openhardware.directory/devices/heltec-meshtower) | [Markdown](https://openhardware.directory/devices/heltec-meshtower/md) ## Prokyber AI-on-the-Edge-Cam Open-source ESP32-S3 camera board with PoE, microSD, and Stemma QT designed for AI-powered utility meter reading using the AI-on-the-edge-device firmware with TensorFlow Lite inference. [Details](https://openhardware.directory/devices/ai-on-the-edge-cam) | [Markdown](https://openhardware.directory/devices/ai-on-the-edge-cam/md) ## M5Stack Atom Echo S3R ESP32-S3 smart speaker dev kit with ES7210 audio codec, NS4168 amplifier, dual MEMS microphones, and RGB LED. Designed for Home Assistant voice assistant, ESPHome, and audio streaming projects. [Details](https://openhardware.directory/devices/m5stack-atom-echo-s3r) | [Markdown](https://openhardware.directory/devices/m5stack-atom-echo-s3r/md) ## DezKVM Go Open-source KVM-over-USB device for controlling headless computers from your laptop. Features HDMI capture up to 1080p 25fps, virtual keyboard/mouse via USB HID, and a browser-based interface requiring no drivers. [Details](https://openhardware.directory/devices/dezkvm-go) | [Markdown](https://openhardware.directory/devices/dezkvm-go/md) ## Sonoff BasicR2 WiFi smart switch based on ESP8285, widely used in the open-source home automation community. Easily flashable with Tasmota or ESPHome for local-only smart home control without cloud dependency. [Details](https://openhardware.directory/devices/sonoff-basicr2) | [Markdown](https://openhardware.directory/devices/sonoff-basicr2/md) ## HestiaPi ONE (Silent) Open-source smart thermostat based on Raspberry Pi Zero W with 3.5\" touchscreen, BME280 sensor, and silent solid-state relays. Fully local control with no cloud dependency, MQTT support, and Home Assistant compatibility. [Details](https://openhardware.directory/devices/hestiapi-one-silent) | [Markdown](https://openhardware.directory/devices/hestiapi-one-silent/md) ## duckyPad Pro 20-key open-source mechanical macropad with duckyScript engine, ESP32-S3, 1.5\" OLED, Bluetooth 5.0, hot-swap switches, dual rotary encoders, and microSD — a powerful Stream Deck alternative. [Details](https://openhardware.directory/devices/duckypad-pro) | [Markdown](https://openhardware.directory/devices/duckypad-pro/md) ## FaikOut WiFi Aircon Controller Open-source ESP32-S3 WiFi controller for Daikin air conditioners with local-only control via MQTT and Home Assistant. Replaces cloud-dependent Daikin WiFi modules with privacy-first, no-internet-required operation. [Details](https://openhardware.directory/devices/faikout-wifi-aircon-controller) | [Markdown](https://openhardware.directory/devices/faikout-wifi-aircon-controller/md) ## Denky D4 Open-source ESP32 Teleinfo reader board for French Linky energy meters. Pre-flashed with Tasmota, features USB-C, WiFi, QWIIC I2C port, and RGB LED. Reads both Standard and Historique TIC formats. [Details](https://openhardware.directory/devices/denky-d4) | [Markdown](https://openhardware.directory/devices/denky-d4/md) ## ESP32 WiFi Fancontroller ESP32-S2-based WiFi fan controller with 4 independent PWM outputs, integrated HDC1080 temperature and humidity sensor, Qwiic expansion, and native Home Assistant integration via ESPHome. [Details](https://openhardware.directory/devices/esp32-wifi-fancontroller) | [Markdown](https://openhardware.directory/devices/esp32-wifi-fancontroller/md) ## Louder Raspberry HAT Plus Open-source Raspberry Pi audio HAT featuring TAS5825M Class-D amplifier with integrated DSP, delivering 32W per channel at 8 ohms. Includes 15-band parametric EQ, FIR filtering, DRC, IR input, and onboard step-down converter to power the Pi from 7-26V. [Details](https://openhardware.directory/devices/louder-raspberry-hat-plus) | [Markdown](https://openhardware.directory/devices/louder-raspberry-hat-plus/md) ## Mesh Detect 2 Open-source ESP32-S3 device that detects FAA Remote ID drone broadcasts and BLE devices, reporting alerts over the Meshtastic LoRa mesh network. Uses XIAO ESP32-S3 + Heltec V3. [Details](https://openhardware.directory/devices/mesh-detect-2) | [Markdown](https://openhardware.directory/devices/mesh-detect-2/md) ## OpenEPaperLink Access Point C6+S3 Open-source dual-MCU access point for wirelessly managing e-paper tags. ESP32-C6 handles WiFi connectivity while ESP32-S3 serves as a 2.4GHz RF transceiver for IEEE 802.15.4 communication with electronic shelf labels. [Details](https://openhardware.directory/devices/openepaperlink-access-point-c6-s3) | [Markdown](https://openhardware.directory/devices/openepaperlink-access-point-c6-s3/md) ## Open AIR Mini Open-source ESP32-based ventilation controller for Ducobox Silent/Focus and Orcon MVS-15xx systems with optional CO2, humidity, VOC, and NOx sensors, fully compatible with ESPHome and Home Assistant. [Details](https://openhardware.directory/devices/open-air-mini) | [Markdown](https://openhardware.directory/devices/open-air-mini/md) ## SLAMTEC RPLiDAR A1 360-degree 2D laser scanner with 12m range and 8000 samples per second. Widely used for ROS robotics, SLAM mapping, and autonomous navigation applications. [Details](https://openhardware.directory/devices/slamtec-rplidar-a1) | [Markdown](https://openhardware.directory/devices/slamtec-rplidar-a1/md) ## HuskyLens AI Camera AI-powered vision sensor with built-in Kendryte K210 processor. Supports face recognition, object tracking, object recognition, line following, color recognition, and tag recognition via I2C or UART. [Details](https://openhardware.directory/devices/huskylens-ai-camera) | [Markdown](https://openhardware.directory/devices/huskylens-ai-camera/md) ## Raspberry Pi 5 The latest Raspberry Pi single-board computer featuring a BCM2712 quad-core Cortex-A76 processor at 2.4GHz, PCIe 2.0, dual 4K HDMI output, USB 3.0, and available in 2GB, 4GB, 8GB, and 16GB RAM configurations. [Details](https://openhardware.directory/devices/raspberry-pi-5) | [Markdown](https://openhardware.directory/devices/raspberry-pi-5/md) ## OV2640 Camera Module 2-megapixel camera module with SCCB/I2C interface, commonly used with ESP32-CAM and other microcontroller boards for image capture, video streaming, and computer vision projects. [Details](https://openhardware.directory/devices/ov2640-camera-module) | [Markdown](https://openhardware.directory/devices/ov2640-camera-module/md) ## Waveshare GPM280 A portable retro gaming console based on Raspberry Pi Compute Module 3+ Lite with a 2.8-inch IPS display (640x480), 1500mAh battery, Wi-Fi ROM updates, and a compact 136.4x67.5mm form factor. [Details](https://openhardware.directory/devices/waveshare-gpm280) | [Markdown](https://openhardware.directory/devices/waveshare-gpm280/md) ## Sonoff ZBMini Zigbee 3.0 two-way smart switch in a tiny form factor that fits behind existing wall switches. Supports external switch input and works with Home Assistant, SmartThings, and other Zigbee hubs. [Details](https://openhardware.directory/devices/sonoff-zbmini) | [Markdown](https://openhardware.directory/devices/sonoff-zbmini/md) ## Home Assistant Connect ZWA-2 Z-Wave 700 series USB stick for Home Assistant, based on Silicon Labs EFR32ZG23. Plug-and-play Z-Wave coordinator with long range support, designed by Nabu Casa for seamless Home Assistant integration. [Details](https://openhardware.directory/devices/home-assistant-connect-zwa-2) | [Markdown](https://openhardware.directory/devices/home-assistant-connect-zwa-2/md) ## Seeed XIAO 2-Channel WiFi AC Relay ESP32-C6 based 2-channel AC relay module with WiFi 6, Zigbee 3.0, and Thread support. Compact relay board compatible with Arduino and ESPHome for smart home AC switching up to 10A per channel. [Details](https://openhardware.directory/devices/seeed-xiao-2-channel-wifi-ac-relay) | [Markdown](https://openhardware.directory/devices/seeed-xiao-2-channel-wifi-ac-relay/md) ## Sonoff SNZB-01P Zigbee 3.0 wireless button and scene switch with single, double, and long press actions. Battery-powered with CR2477 lasting up to 5 years. Works with Home Assistant, Zigbee2MQTT, and eWeLink. [Details](https://openhardware.directory/devices/sonoff-snzb-01p) | [Markdown](https://openhardware.directory/devices/sonoff-snzb-01p/md) ## M5Stack Single Live Wire WiFi Smart Switch ESP32-C6 based WiFi smart switch for single live wire AC power control. Supports WiFi 6 and Zigbee 3.0, fits standard wall boxes for home automation. [Details](https://openhardware.directory/devices/m5stack-wifi-smart-switch) | [Markdown](https://openhardware.directory/devices/m5stack-wifi-smart-switch/md) ## M5Stack Air Quality Kit v1.1 ESP32-S3 based air quality monitor with SEN55 particulate/VOC sensor, SCD40 CO2 sensor, 1.54" e-ink display, 600mAh battery, and Grove connector. [Details](https://openhardware.directory/devices/m5stack-air-quality-kit) | [Markdown](https://openhardware.directory/devices/m5stack-air-quality-kit/md) ## DFRobot Gravity Flexible RGB LED Matrix Flexible addressable RGB LED matrix panel with I2C control and Gravity connector, available in 8x8, 8x32, and 16x16 configurations for visual displays and lighting projects. [Details](https://openhardware.directory/devices/dfrobot-gravity-rgb-led-matrix) | [Markdown](https://openhardware.directory/devices/dfrobot-gravity-rgb-led-matrix/md) ## M5Stack ENV III Unit I2C environmental sensor unit with SHT30 temperature/humidity and QMP6988 barometric pressure sensors. Grove connector, compatible with M5Stack ecosystem. [Details](https://openhardware.directory/devices/m5stack-env-iii-unit) | [Markdown](https://openhardware.directory/devices/m5stack-env-iii-unit/md) ## DFRobot Pan-Tilt HAT 2-axis servo-driven pan-tilt platform HAT for Raspberry Pi and NVIDIA Jetson Nano, ideal for camera tracking, FPV, and robotics head movement projects. [Details](https://openhardware.directory/devices/dfrobot-pan-tilt-hat) | [Markdown](https://openhardware.directory/devices/dfrobot-pan-tilt-hat/md) ## M5Stack UnitV2 AI Camera Linux-based standalone AI camera with SigmaStar SSD202D dual-core Cortex-A7, GC4653 4MP sensor, 128MB RAM, WiFi, and USB-C. Runs Python and V-Training for edge AI. [Details](https://openhardware.directory/devices/m5stack-unitv2-ai-camera) | [Markdown](https://openhardware.directory/devices/m5stack-unitv2-ai-camera/md) ## DFPlayer Mini MP3 Module Compact MP3/WAV/WMA audio player module with microSD slot, UART serial control, and built-in 3W amplifier — one of the most popular audio modules for Arduino and IoT projects. [Details](https://openhardware.directory/devices/dfplayer-mini) | [Markdown](https://openhardware.directory/devices/dfplayer-mini/md) ## M5Stack GPS Module V2.1 ATGM336H-based GPS/GNSS module supporting GPS, BeiDou, Galileo, GLONASS with external active antenna, DIP switch for TX/RX config, and PPS output. [Details](https://openhardware.directory/devices/m5stack-gps-module-v21) | [Markdown](https://openhardware.directory/devices/m5stack-gps-module-v21/md) ## WS2812B RGB LED Ring (12-Bit, 50mm) 12-LED addressable WS2812B RGB ring in a 50mm form factor, running on 5V with single-wire data control — perfect for status indicators, wearables, and visual effects. [Details](https://openhardware.directory/devices/ws2812b-rgb-led-ring) | [Markdown](https://openhardware.directory/devices/ws2812b-rgb-led-ring/md) ## Waveshare DDSM115 Direct Drive Servo Motor All-in-one 115 RPM direct drive servo hub motor with RS485 control, 4096-position encoder, and IP54 rating — designed for robotics, AGVs, and precision motion applications. [Details](https://openhardware.directory/devices/waveshare-ddsm115) | [Markdown](https://openhardware.directory/devices/waveshare-ddsm115/md) ## Waveshare DDSM315 Direct Drive Servo Motor High-speed 315 RPM direct drive servo motor with RS485 bus, 12-bit encoder, and IP54 waterproof rating — ideal for RC cars, mobile robots, and DIY robotics platforms. [Details](https://openhardware.directory/devices/waveshare-ddsm315) | [Markdown](https://openhardware.directory/devices/waveshare-ddsm315/md) ## Holybro M10 GPS u-blox M10 GPS module with IST8310 compass for Pixhawk flight controllers. Supports GPS, GLONASS, Galileo, and BeiDou constellations with onboard safety switch, buzzer, and LED indicator. [Details](https://openhardware.directory/devices/holybro-m10-gps) | [Markdown](https://openhardware.directory/devices/holybro-m10-gps/md) ## WiFi Devboard for Flipper Zero ESP32-S2-based WiFi development board for Flipper Zero enabling wireless firmware updates, Black Magic Probe debugging over USB and WiFi, and WiFi pentesting with PMKID capture and deauth capabilities. [Details](https://openhardware.directory/devices/flipper-zero-wifi-devboard) | [Markdown](https://openhardware.directory/devices/flipper-zero-wifi-devboard/md) ## Flipper Zero Video Game Module RP2040-powered expansion module for Flipper Zero with DVI-D video output, 6-axis IMU motion sensor, 14-pin GPIO breakout, and USB-C. Fully open-source firmware and schematics. [Details](https://openhardware.directory/devices/flipper-zero-video-game-module) | [Markdown](https://openhardware.directory/devices/flipper-zero-video-game-module/md) ## Flipper Zero Portable open-source multi-tool for hardware exploration, combining Sub-GHz, NFC, RFID 125kHz, infrared, iButton, BLE, and GPIO in a pocket-sized device with a 1.4" monochrome LCD. [Details](https://openhardware.directory/devices/flipper-zero) | [Markdown](https://openhardware.directory/devices/flipper-zero/md) ## TinkerNav RTK GNSS Board Open-source RTK GNSS board with SkyTraq PX1105R receiver and ESP32-S3 for centimeter-level positioning. Works as base station or rover with WiFi, Bluetooth LE, and optional LoRa connectivity. [Details](https://openhardware.directory/devices/tinkernav-rtk-gnss-board) | [Markdown](https://openhardware.directory/devices/tinkernav-rtk-gnss-board/md) ## VoltLink CP2102N Open source USB-to-serial adapter and ESP32 programmer featuring a genuine Silabs CP2102N chip, USB-C connector, auto-reset circuitry, 3.3V 500mA regulator, and ESD/overcurrent protection. [Details](https://openhardware.directory/devices/voltlink-cp2102n) | [Markdown](https://openhardware.directory/devices/voltlink-cp2102n/md) ## UkieLab WiFi Weather Station 7.5" A smart WiFi-enabled weather station with a 7.5\" e-ink display showing current conditions, humidity, pressure, and 4-day forecasts via Apple Weather. Available in USB-powered or battery-powered versions with optional CO2 sensor. [Details](https://openhardware.directory/devices/ukielab-wifi-weather-station-75) | [Markdown](https://openhardware.directory/devices/ukielab-wifi-weather-station-75/md) ## Oui-Spy ESP32-S3 based multi-mode BLE detection and security research tool with integrated piezo buzzer, MMCX antenna connector, and seven swappable firmware modes for surveillance detection, drone tracking, and RF direction finding. [Details](https://openhardware.directory/devices/oui-spy) | [Markdown](https://openhardware.directory/devices/oui-spy/md) ## ChameleonUltra Open-source NFC/RFID multi-tool built on the nRF52840 SoC. Reads, writes, cracks, and emulates 13.56MHz and 125kHz cards in a compact key-fob form factor with BLE 5.0 connectivity. [Details](https://openhardware.directory/devices/chameleon-ultra) | [Markdown](https://openhardware.directory/devices/chameleon-ultra/md) ## Makerfabs ESP32 UWB Pro with Display ESP32-WROVER development board with Decawave DWM1000 UWB module for centimeter-accurate indoor positioning and ranging, featuring a 1.3\" OLED display and LiPo battery charging. [Details](https://openhardware.directory/devices/makerfabs-esp32-uwb-pro-with-display) | [Markdown](https://openhardware.directory/devices/makerfabs-esp32-uwb-pro-with-display/md) ## AVR-HF ADX-MI3 Pre-built digital mode QRP transceiver for amateur radio, supporting FT8, FT4, JS8, and WSPR on HF bands from 160m to 6m with ~5W output, OLED display, and single USB-C cable operation. [Details](https://openhardware.directory/devices/avr-hf-adx-mi3) | [Markdown](https://openhardware.directory/devices/avr-hf-adx-mi3/md) ## Evil Crow RF V2 Open-source RF security research tool with ESP32, dual CC1101 sub-GHz transceivers (300-928MHz), and NRF24L01 2.4GHz module for penetration testing, signal analysis, and replay attacks. [Details](https://openhardware.directory/devices/evil-crow-rf-v2) | [Markdown](https://openhardware.directory/devices/evil-crow-rf-v2/md) ## Louder ESP32 ESP32 audio development board with TAS5805M I2S Class-D amplifier delivering 2x23W stereo output, designed for multi-room audio, network streaming, and smart home integration. [Details](https://openhardware.directory/devices/louder-esp32) | [Markdown](https://openhardware.directory/devices/louder-esp32/md) ## Gnat LoRa+GNSS Asset Tracker Ultra-small (20x20mm), ultra-low-power LoRa/LoRaWAN + concurrent GNSS asset tracker by Tlera Corp, built on the Murata CMWX1ZZABZ-078 module with STM32L082 MCU, SX1276 LoRa radio, u-blox MAX-M8Q GNSS, and LIS2DW12 accelerometer. [Details](https://openhardware.directory/devices/gnat-loragnss-asset-tracker) | [Markdown](https://openhardware.directory/devices/gnat-loragnss-asset-tracker/md) ## Airlytix ES1 ESPHome-native indoor air quality sensor with PM1.0/PM2.5/PM4/PM10, CO2, VOC, NOx, temperature, humidity, pressure, light, and sound monitoring. Designed for Home Assistant with full local control and open YAML configuration. [Details](https://openhardware.directory/devices/airlytix-es1) | [Markdown](https://openhardware.directory/devices/airlytix-es1/md) ## Elecrow ThinkNode M1 Compact Meshtastic LoRa transceiver with nRF52840, SX1262, 1.54\" e-paper display, GPS, and 1200mAh battery for off-grid mesh communication. [Details](https://openhardware.directory/devices/elecrow-thinknode-m1) | [Markdown](https://openhardware.directory/devices/elecrow-thinknode-m1/md) ## CircuitMess ClockStar 2.0 DIY smartwatch kit powered by ESP32 with ST7735S display, 6-axis IMU, Bluetooth connectivity, and programmable via CircuitBlocks visual coding environment. [Details](https://openhardware.directory/devices/circuitmess-clockstar-2-0) | [Markdown](https://openhardware.directory/devices/circuitmess-clockstar-2-0/md) ## CircuitMess NASA Artemis Watch 2.0 NASA-themed programmable smartwatch powered by ESP32-S3 with BLE 5.0, 6-axis IMU, ST7735S display, and activity tracking. Pre-assembled and ready to code. [Details](https://openhardware.directory/devices/circuitmess-nasa-artemis-watch-2-0) | [Markdown](https://openhardware.directory/devices/circuitmess-nasa-artemis-watch-2-0/md) ## CircuitMess Chatter 2.0 DIY encrypted LoRa communicator kit building a pair of devices for off-grid text messaging up to 2km range. Features ESP32, LLCC68 LoRa radio, and 160×128 TFT display. [Details](https://openhardware.directory/devices/circuitmess-chatter-2-0) | [Markdown](https://openhardware.directory/devices/circuitmess-chatter-2-0/md) ## CircuitMess ByteBoi 2.0 DIY retro game console kit powered by ESP32 with TFT color display, speaker, microSD card slot, and RGB LED. Build it, play pre-loaded games, then code your own. [Details](https://openhardware.directory/devices/circuitmess-byteboi-2-0) | [Markdown](https://openhardware.directory/devices/circuitmess-byteboi-2-0/md) ## CircuitMess NASA Mars Perseverance Rover NASA-themed DIY robotics kit with ESP32-S3, camera, dual DC motors, 3 servos, and WiFi/BLE. Build a programmable Mars Rover replica with robotic arm and live video feed. [Details](https://openhardware.directory/devices/circuitmess-nasa-mars-perseverance-rover) | [Markdown](https://openhardware.directory/devices/circuitmess-nasa-mars-perseverance-rover/md) ## Shelly Plus 1 ESP32-C3 based WiFi/BLE smart relay module with 16A switching capacity, dry contact input, and compact DIN-rail or in-wall form factor. Flashable with Tasmota or ESPHome for local smart home control. [Details](https://openhardware.directory/devices/shelly-plus-1) | [Markdown](https://openhardware.directory/devices/shelly-plus-1/md) ## Sonoff NSPanel ESP32-based smart wall switch with 3.5-inch capacitive touchscreen, dual relay outputs, temperature sensor, and buzzer. Flashable with Tasmota for custom LVGL/Berry interfaces and Home Assistant integration. [Details](https://openhardware.directory/devices/sonoff-nspanel) | [Markdown](https://openhardware.directory/devices/sonoff-nspanel/md) ## Sonoff MINIR4 Extreme Ultra-compact ESP32-C3 WiFi smart switch module with 10A relay, detached switch mode, and the smallest form factor in its class. Fits any wall box. Flashable with Tasmota for local control. [Details](https://openhardware.directory/devices/sonoff-minir4-extreme) | [Markdown](https://openhardware.directory/devices/sonoff-minir4-extreme/md) ## Shelly Plus 2PM ESP32-based dual-relay WiFi/BLE smart switch with per-channel power monitoring via ADE7953, cover/shutter control mode, and 10A per channel. Flashable with Tasmota for local roller blind and dual light control. [Details](https://openhardware.directory/devices/shelly-plus-2pm) | [Markdown](https://openhardware.directory/devices/shelly-plus-2pm/md) ## Sonoff POW Elite 16A ESP32-based WiFi smart switch with high-accuracy power monitoring via CSE7766, 16A relay, LCD display, and DIN-rail mounting. Flashable with Tasmota for local energy tracking and home automation. [Details](https://openhardware.directory/devices/sonoff-pow-elite-16a) | [Markdown](https://openhardware.directory/devices/sonoff-pow-elite-16a/md) ## Sonoff Dual R3 ESP32-based dual-relay WiFi smart switch with per-channel power monitoring, roller shutter mode, and 2×10A outputs. Ideal for motorized blinds with Tasmota shutter calibration and position tracking. [Details](https://openhardware.directory/devices/sonoff-dual-r3) | [Markdown](https://openhardware.directory/devices/sonoff-dual-r3/md) ## Sonoff Zigbee Bridge Pro ESP32-based Zigbee-to-WiFi gateway with CC2652P coordinator chip supporting 128 Zigbee devices. Flashable with Tasmota for local Zigbee bridge operation with Home Assistant via MQTT. [Details](https://openhardware.directory/devices/sonoff-zigbee-bridge-pro) | [Markdown](https://openhardware.directory/devices/sonoff-zigbee-bridge-pro/md) ## DFRobot Beetle CM-32U4 Ultra-compact Arduino Leonardo-compatible microcontroller board with ATmega32U4, integrated lithium battery charging, and native USB in a tiny 22x20.5mm form factor. [Details](https://openhardware.directory/devices/dfrobot-beetle-cm-32u4) | [Markdown](https://openhardware.directory/devices/dfrobot-beetle-cm-32u4/md) ## DFRobot Beetle ESP32-C3 Coin-sized ESP32-C3 RISC-V IoT development board with WiFi, BLE 5.0, integrated LiPo charging, 13 GPIO pins, and USB-C in a 25x20.5mm form factor. [Details](https://openhardware.directory/devices/dfrobot-beetle-esp32-c3) | [Markdown](https://openhardware.directory/devices/dfrobot-beetle-esp32-c3/md) ## Pine64 PineTime Open-source smartwatch built on the Nordic nRF52832 SoC with 1.3-inch IPS touchscreen, heart rate sensor, accelerometer, and week-long battery life. Runs InfiniTime, Wasp-OS, or Zephyr firmware. Priced from $27. [Details](https://openhardware.directory/devices/pine64-pinetime) | [Markdown](https://openhardware.directory/devices/pine64-pinetime/md) ## DFRobot Beetle ESP32 Compact ESP32 dual-core development board with WiFi, Bluetooth 4.2, sewable I/O pads, and wearable-friendly 35x34mm form factor for IoT and e-textile projects. [Details](https://openhardware.directory/devices/dfrobot-beetle-esp32) | [Markdown](https://openhardware.directory/devices/dfrobot-beetle-esp32/md) ## DFRobot Beetle RP2040 Compact RP2040 dual-core ARM Cortex-M0+ development board with USB-C, 8 GPIO pins, and beginner-friendly immersion gold pads in a 27x20mm form factor. [Details](https://openhardware.directory/devices/dfrobot-beetle-rp2040) | [Markdown](https://openhardware.directory/devices/dfrobot-beetle-rp2040/md) ## DFRobot Beetle RP2350 Ultra-affordable RP2350 dual-architecture development board with switchable ARM Cortex-M33 / RISC-V cores, LiPo charging, 11 GPIO pins, and USB-C in a 25x20.5mm package. [Details](https://openhardware.directory/devices/dfrobot-beetle-rp2350) | [Markdown](https://openhardware.directory/devices/dfrobot-beetle-rp2350/md) ## Waveshare UGV Rover Open-source 6-wheel 4WD AI robot platform with dual-controller architecture (ESP32 + Raspberry Pi), computer vision, pan-tilt camera, ESP-NOW communication, and ROS2 support for robotics education and autonomous navigation. [Details](https://openhardware.directory/devices/waveshare-ugv-rover) | [Markdown](https://openhardware.directory/devices/waveshare-ugv-rover/md) ## D-Robotics RDK X3 AI-focused single board computer with 5 TOPS NPU, quad-core ARM Cortex-A53, 4GB LPDDR4, dual MIPI CSI cameras, and ROS2 support for robotics and edge AI. [Details](https://openhardware.directory/devices/d-robotics-rdk-x3) | [Markdown](https://openhardware.directory/devices/d-robotics-rdk-x3/md) ## Ai-Thinker Ra-09-DTU Intelligent wireless LoRaWAN DTU with isolated RS485 interface, powered by STM32WLE5CCU6 ARM Cortex-M4 MCU with integrated Sub-GHz radio. Wide 6-36V input for industrial deployment. [Details](https://openhardware.directory/devices/ai-thinker-ra-09-dtu) | [Markdown](https://openhardware.directory/devices/ai-thinker-ra-09-dtu/md) ## D-Robotics RDK X5 High-performance AI SBC with 10 TOPS NPU, octa-core ARM Cortex-A55, 8GB LPDDR4, WiFi 6, 4x USB 3.0, dual MIPI CSI, CAN FD, and ROS2 support for advanced robotics. [Details](https://openhardware.directory/devices/d-robotics-rdk-x5) | [Markdown](https://openhardware.directory/devices/d-robotics-rdk-x5/md) ## Waveshare ESP32-P4-Pico Compact Pico-form-factor development board based on the ESP32-P4 RISC-V dual-core processor at 400MHz with 32MB PSRAM, 32MB flash, MIPI-DSI/CSI interfaces, onboard ES8311 audio codec with NS4150B amplifier, microSD slot, and USB 2.0 OTG HS. [Details](https://openhardware.directory/devices/waveshare-esp32-p4-pico) | [Markdown](https://openhardware.directory/devices/waveshare-esp32-p4-pico/md) ## DFRobot Beetle BLE Ultra-compact Arduino Uno-compatible board with BLE 4.0 (CC2540), ATmega328P, sewable gold-plated I/O pads, and wireless programming in a 28.8x33.1mm wearable form factor. [Details](https://openhardware.directory/devices/dfrobot-beetle-ble) | [Markdown](https://openhardware.directory/devices/dfrobot-beetle-ble/md) ## DFRobot Beetle Board The original coin-sized Arduino Leonardo-compatible board with ATmega32U4, native USB, 10 digital and 5 analog pins, and sewable gold-plated pads in a 20x22mm form factor. [Details](https://openhardware.directory/devices/dfrobot-beetle-board) | [Markdown](https://openhardware.directory/devices/dfrobot-beetle-board/md) ## Waveshare WAVE ROVER Flexible 4WD mobile robot chassis with all-metal body, ESP32 controller, 0.91\" OLED, 9-axis IMU, 3S UPS power system, and open-source firmware. Supports Raspberry Pi and Jetson Nano as host computers. [Details](https://openhardware.directory/devices/waveshare-wave-rover) | [Markdown](https://openhardware.directory/devices/waveshare-wave-rover/md) ## Waveshare RaspRover Open-source 4WD AI robot with dual-controller architecture (ESP32 + Raspberry Pi), 5MP 160-degree camera, pan-tilt module, audio system, computer vision via OpenCV/MediaPipe, and ROS2 support for AI robotics education. [Details](https://openhardware.directory/devices/waveshare-rasprover) | [Markdown](https://openhardware.directory/devices/waveshare-rasprover/md) ## Waveshare Cobra Flex All-metal modular drive-by-wire 4WD robot chassis with ESP32-S3 controller, hub motors with built-in FOC control, CNC metal suspension, LIN bus communication, IP32 protection, and 12 kg payload capacity for heavy-duty robotics. [Details](https://openhardware.directory/devices/waveshare-cobra-flex) | [Markdown](https://openhardware.directory/devices/waveshare-cobra-flex/md) ## DFRobot ESP32-S3 AI Camera ESP32-S3 AI camera module with 2MP wide-angle night vision sensor, I2S speaker and microphone, ambient light sensor, WiFi/BLE 5.0, and edge AI inference support in a 42x42mm package. [Details](https://openhardware.directory/devices/dfrobot-esp32-s3-ai-camera) | [Markdown](https://openhardware.directory/devices/dfrobot-esp32-s3-ai-camera/md) ## Waveshare CM5-DUAL-ETH-BASE Gigabit + 2.5G dual Ethernet base board for Raspberry Pi Compute Module 5 with M.2 NVMe slot, dual HDMI 4K output, dual MIPI interfaces, wide 7-36V input, EEPROM, and encryption chip for industrial IoT applications. [Details](https://openhardware.directory/devices/waveshare-cm5-dual-eth-base) | [Markdown](https://openhardware.directory/devices/waveshare-cm5-dual-eth-base/md) ## Waveshare ESP32-P4-WIFI6 Pico-form-factor development board combining the ESP32-P4 RISC-V dual-core at 400MHz with an ESP32-C6 co-processor for WiFi 6 and Bluetooth 5 LE. Features 32MB PSRAM, 32MB flash, MIPI-DSI/CSI, onboard audio, microSD, and USB 2.0 OTG HS. [Details](https://openhardware.directory/devices/waveshare-esp32-p4-wifi6) | [Markdown](https://openhardware.directory/devices/waveshare-esp32-p4-wifi6/md) ## Waveshare ESP32-P4-ETH Pico-form-factor development board with ESP32-P4 RISC-V dual-core at 400MHz, 100Mbps Ethernet via IP101 PHY, 32MB PSRAM, 32MB flash, MIPI-DSI/CSI interfaces, onboard ES8311 audio codec with amplifier, microSD, USB 2.0 OTG HS, and PoE module header. [Details](https://openhardware.directory/devices/waveshare-esp32-p4-eth) | [Markdown](https://openhardware.directory/devices/waveshare-esp32-p4-eth/md) ## Waveshare ESP32-S3-RS485-CAN Industrial ESP32-S3 control board with isolated RS-485 and CAN bus interfaces, 7-36V wide voltage input, PCF85063 RTC, DIN rail enclosure, and WiFi/Bluetooth for industrial IoT and automation applications. [Details](https://openhardware.directory/devices/waveshare-esp32-s3-rs485-can) | [Markdown](https://openhardware.directory/devices/waveshare-esp32-s3-rs485-can/md) ## Waveshare ESP32-P4-WIFI6-DEV-KIT Full-featured ESP32-P4 development board with WiFi 6 and Bluetooth 5 LE via ESP32-C6, 100Mbps Ethernet, PoE header, 3.5mm headphone jack, USB OTG HS switchable host/device, 16MB flash, 32MB PSRAM, MIPI-DSI/CSI, and 28 GPIOs. [Details](https://openhardware.directory/devices/waveshare-esp32-p4-wifi6-dev-kit) | [Markdown](https://openhardware.directory/devices/waveshare-esp32-p4-wifi6-dev-kit/md) ## Waveshare ESP32-S3-POE-ETH-8DI-8DO Industrial ESP32-S3 controller with 8-channel optocoupler-isolated digital inputs (5-36V), 8-channel Darlington outputs (500mA each), PoE Ethernet (W5500), isolated RS-485 and CAN bus, RTC, and DIN rail enclosure. [Details](https://openhardware.directory/devices/waveshare-esp32-s3-poe-eth-8di-8do) | [Markdown](https://openhardware.directory/devices/waveshare-esp32-s3-poe-eth-8di-8do/md) ## Waveshare ESP32-P4-WIFI6-POE-ETH ESP32-P4 development board with WiFi 6 and Bluetooth 5 LE via ESP32-C6, 100Mbps PoE Ethernet via IP101GRI, IPEX external antenna, USB Type-A OTG HS, 32MB PSRAM, 16MB flash, MIPI-DSI/CSI, onboard audio, and 28 GPIOs. [Details](https://openhardware.directory/devices/waveshare-esp32-p4-wifi6-poe-eth) | [Markdown](https://openhardware.directory/devices/waveshare-esp32-p4-wifi6-poe-eth/md) ## Arduino Nano Matter Ultra-compact Matter/Thread/BLE development board based on Silicon Labs MGM240S, bringing official Matter support to the beloved Arduino Nano form factor at 45×18mm. [Details](https://openhardware.directory/devices/arduino-nano-matter) | [Markdown](https://openhardware.directory/devices/arduino-nano-matter/md) ## Olimex ESP32-C6-EVB Open-source hardware evaluation board with ESP32-C6, 4 mains-rated relays, 4 opto-isolated inputs, and WiFi 6/Thread/Zigbee/Matter connectivity for home and industrial automation. [Details](https://openhardware.directory/devices/olimex-esp32-c6-evb) | [Markdown](https://openhardware.directory/devices/olimex-esp32-c6-evb/md) ## SparkFun Thing Plus Matter - MGM240P Feather-compatible Matter/Thread/Zigbee/BLE dev board based on Silicon Labs MGM240P with Qwiic, LiPo charging, microSD, and +20dBm radio range. [Details](https://openhardware.directory/devices/sparkfun-thing-plus-matter-mgm240p) | [Markdown](https://openhardware.directory/devices/sparkfun-thing-plus-matter-mgm240p/md) ## Olimex ESP32-C6-DevKit-Lipo Breadboard-friendly open-source ESP32-C6 dev board with WiFi 6, Thread, Zigbee, BLE 5, built-in LiPo charger, and dual USB-C — all for under €9. [Details](https://openhardware.directory/devices/olimex-esp32-c6-devkit-lipo) | [Markdown](https://openhardware.directory/devices/olimex-esp32-c6-devkit-lipo/md) ## Olimex ESP32-H2-DevKit-LiPo Ultra-affordable open-source ESP32-H2 dev board for Thread, Zigbee, and Matter — BLE 5, LiPo charging, Qwiic/Stemma, dual USB-C, for €5.95. [Details](https://openhardware.directory/devices/olimex-esp32-h2-devkit-lipo) | [Markdown](https://openhardware.directory/devices/olimex-esp32-h2-devkit-lipo/md) ## DFRobot FireBeetle 2 ESP32-C6 Low-cost ESP32-C6 IoT board with WiFi 6, BLE 5, Thread, Zigbee, Matter, solar panel charging with MPPT, and ultra-low 16µA deep sleep — for $5.90. [Details](https://openhardware.directory/devices/dfrobot-firebeetle-2-esp32-c6) | [Markdown](https://openhardware.directory/devices/dfrobot-firebeetle-2-esp32-c6/md) ## DFRobot Beetle ESP32-C6 Coin-sized (25×20.5mm) ESP32-C6 wearable dev board with WiFi 6, BLE 5, Thread, Zigbee, Matter, integrated LiPo charger, and 14µA deep sleep — for $4.90. [Details](https://openhardware.directory/devices/dfrobot-beetle-esp32-c6) | [Markdown](https://openhardware.directory/devices/dfrobot-beetle-esp32-c6/md) ## Seeed Studio XIAO ESP32C6 Thumb-sized (21×17.8mm) Matter/Thread/Zigbee/WiFi 6/BLE 5.3 dev board with dual RISC-V cores, onboard antenna, 15µA deep sleep, and hardware security — for ~$5. [Details](https://openhardware.directory/devices/seeed-xiao-esp32c6) | [Markdown](https://openhardware.directory/devices/seeed-xiao-esp32c6/md) ## Adafruit ESP32-C6 Feather Open-source Feather-form-factor ESP32-C6 board with WiFi 6, BLE 5, Thread, Zigbee, STEMMA QT, NeoPixel, LiPo charging with MAX17048, and CircuitPython support — $14.95. [Details](https://openhardware.directory/devices/adafruit-esp32-c6-feather) | [Markdown](https://openhardware.directory/devices/adafruit-esp32-c6-feather/md) ## Radxa Rock 5B High-performance Rockchip RK3588 SBC from Radxa with up to 32GB LPDDR4X, NVMe M.2, WiFi 6, 2.5GbE, and USB-C PD power — a flagship Linux board in the Raspberry Pi 4 form factor. [Details](https://openhardware.directory/devices/radxa-rock-5b) | [Markdown](https://openhardware.directory/devices/radxa-rock-5b/md) ## Banana Pi M5 Banana Pi M5 is a quad-core SBC powered by the Amlogic S905X3 SoC with 4GB LPDDR4 RAM, 16GB eMMC, four USB 3.0 ports, and Gigabit Ethernet, running Armbian Linux. [Details](https://openhardware.directory/devices/bananapi-m5) | [Markdown](https://openhardware.directory/devices/bananapi-m5/md) ## Radxa Rock 5 ITX Mini-ITX single-board computer powered by Rockchip RK3588 with 16GB LPDDR4X, dual NVMe slots, dual 2.5GbE, PCIe x4, ATX power, and WiFi 6 — a true desktop motherboard replacement. [Details](https://openhardware.directory/devices/radxa-rock-5-itx) | [Markdown](https://openhardware.directory/devices/radxa-rock-5-itx/md) ## Radxa Rock 4D Mid-range Rockchip RK3576 SBC from Radxa with up to 8GB LPDDR4X, NVMe M.2, WiFi 6, Gigabit Ethernet, and USB 3.0 — a capable Linux board in a compact footprint. [Details](https://openhardware.directory/devices/radxa-rock-4d) | [Markdown](https://openhardware.directory/devices/radxa-rock-4d/md) ## Banana Pi M7 Banana Pi M7 is a high-performance SBC powered by the Rockchip RK3588 octa-core SoC with up to 32GB LPDDR4X, NVMe SSD support, WiFi 6, dual 2.5GbE, and USB-C PD power. [Details](https://openhardware.directory/devices/bananapi-m7) | [Markdown](https://openhardware.directory/devices/bananapi-m7/md) ## Radxa Rock 3A Affordable Rockchip RK3568 quad-core SBC from Radxa with up to 8GB LPDDR4, eMMC, microSD, Gigabit Ethernet, USB 3.0, PCIe, and M.2 expansion — no built-in WiFi, powered via USB-C or 12V DC. [Details](https://openhardware.directory/devices/radxa-rock-3a) | [Markdown](https://openhardware.directory/devices/radxa-rock-3a/md) ## Banana Pi M2S Banana Pi M2S is a hexa-core SBC powered by the Amlogic S922X SoC with 4GB DDR4, 16GB eMMC, WiFi 5, Bluetooth 5.0, four USB 3.0 ports, and Gigabit Ethernet. [Details](https://openhardware.directory/devices/bananapi-m2s) | [Markdown](https://openhardware.directory/devices/bananapi-m2s/md) ## Radxa Zero 3W Credit-card sized Rockchip RK3566 SBC with up to 4GB LPDDR4, eMMC, microSD, WiFi 5, Bluetooth 5.0, and USB-C OTG — a compact headless Linux board with no Ethernet port. [Details](https://openhardware.directory/devices/radxa-zero-3) | [Markdown](https://openhardware.directory/devices/radxa-zero-3/md) ## Banana Pi M2 Pro Banana Pi M2 Pro is a compact SBC powered by the Amlogic S905X3 with 2GB DDR4, 16GB eMMC, WiFi 5, Bluetooth 5.0, three USB 3.0 ports, and USB-C power input. [Details](https://openhardware.directory/devices/bananapi-m2-pro) | [Markdown](https://openhardware.directory/devices/bananapi-m2-pro/md) ## MKS KLIPAD50 MKS/Makerbase 5-inch Klipper touchscreen panel based on Rockchip RK3328, with 800×480 IPS display, 1GB RAM, 8GB eMMC, WiFi, and USB-C power — purpose-built for 3D printer Klipper control interfaces. [Details](https://openhardware.directory/devices/mks-klipad50) | [Markdown](https://openhardware.directory/devices/mks-klipad50/md) ## Radxa Rock S0 Tiny Rockchip RK3308B SBC with up to 512MB DDR3, 8GB eMMC, microSD, WiFi 4, Bluetooth 5.0, and USB-C OTG — a postage-stamp Linux board for IoT and audio applications. [Details](https://openhardware.directory/devices/radxa-rock-s0) | [Markdown](https://openhardware.directory/devices/radxa-rock-s0/md) ## Banana Pi CM4 IO Banana Pi CM4 IO is an SBC carrier board for the BPI-CM4 compute module, featuring RK3566, 4GB LPDDR4, 32GB eMMC, WiFi 5, PCIe, HDMI, and Gigabit Ethernet. [Details](https://openhardware.directory/devices/bananapi-cm4-io) | [Markdown](https://openhardware.directory/devices/bananapi-cm4-io/md) ## Radxa E25 Fanless Rockchip RK3568J gateway and router board with dual 2.5GbE, 4x USB 3.0, mini-PCIe with SIM slot, M.2 NVMe, and 2GB/4GB LPDDR4 — designed for networking and industrial IoT. [Details](https://openhardware.directory/devices/radxa-e25) | [Markdown](https://openhardware.directory/devices/radxa-e25/md) ## Banana Pi F3 Banana Pi F3 is a RISC-V single-board computer powered by the SpacemiT K1 octa-core SoC with 4GB/8GB LPDDR4X, 16GB/32GB eMMC, WiFi 6, Bluetooth 5.2, and Gigabit Ethernet. [Details](https://openhardware.directory/devices/bananapi-f3) | [Markdown](https://openhardware.directory/devices/bananapi-f3/md) ## Radxa E52C Compact Rockchip RK3582 router and gateway board with 4GB/8GB LPDDR4X, dual 2.5GbE, mini-PCIe with SIM slot, USB 3.0, and eMMC — ideal for network appliances and edge computing. [Details](https://openhardware.directory/devices/radxa-e52c) | [Markdown](https://openhardware.directory/devices/radxa-e52c/md) ## Banana Pi M2+ Banana Pi M2+ is a compact SBC powered by the Allwinner H3 quad-core SoC with 1GB DDR3, 8GB eMMC, 802.11n WiFi, Bluetooth 4.0, four USB 2.0 ports, and micro-USB power. [Details](https://openhardware.directory/devices/bananapi-m2-plus) | [Markdown](https://openhardware.directory/devices/bananapi-m2-plus/md) ## Radxa E54C High-performance Rockchip RK3588S edge gateway with 8GB LPDDR4X, 4x Gigabit Ethernet ports (RTL8367RB switch), PCIe expansion, USB 3.0, HDMI, and 12V DC power — built for demanding network and edge AI workloads. [Details](https://openhardware.directory/devices/radxa-e54c) | [Markdown](https://openhardware.directory/devices/radxa-e54c/md) ## Banana Pi M4 Zero Banana Pi M4 Zero is a compact Zero-form-factor SBC powered by the Rockchip RK3528 quad-core SoC with up to 4GB DDR4, 16GB eMMC, WiFi 5, Bluetooth 5.0, and USB-C power. [Details](https://openhardware.directory/devices/bananapi-m4-zero) | [Markdown](https://openhardware.directory/devices/bananapi-m4-zero/md) ## Radxa Rockpi E Compact Rockchip RK3328 SBC with up to 4GB DDR4, eMMC, microSD, Gigabit + Fast Ethernet, USB 3.0, optional WiFi/BT, and USB-C power — a versatile small Linux board for networking and IoT. [Details](https://openhardware.directory/devices/radxa-rockpi-e) | [Markdown](https://openhardware.directory/devices/radxa-rockpi-e/md) ## Radxa Rockpi S Tiny Rockchip RK3308 quad-core SBC with up to 512MB DDR3, 8GB eMMC, microSD, 100Mbps Ethernet, USB 2.0, optional WiFi/BT, and USB-C — a miniature Linux board for audio and IoT projects. [Details](https://openhardware.directory/devices/radxa-rockpi-s) | [Markdown](https://openhardware.directory/devices/radxa-rockpi-s/md) ## BIGTREETECH CB1 V2.2 Compact Linux compute module by BIGTREETECH, powered by the Allwinner H616 SoC with 1GB DDR3, 100M WiFi + 100M Ethernet, and microSD — designed as a drop-in Raspberry Pi CM4 replacement for 3D printer boards running Klipper. [Details](https://openhardware.directory/devices/bigtreetech-cb1) | [Markdown](https://openhardware.directory/devices/bigtreetech-cb1/md) ## ODROID-C1 Hardkernel ODROID-C1 — affordable quad-core Cortex-A5 SBC with 1GB DDR3, Fast Ethernet, and four USB 2.0 ports, one of the earliest Raspberry Pi competitors running Armbian. [Details](https://openhardware.directory/devices/odroid-c1) | [Markdown](https://openhardware.directory/devices/odroid-c1/md) ## Tinker Board / S Raspberry Pi form factor SBC by ASUS featuring the Rockchip RK3288 SoC, 2GB LPDDR3, WiFi 802.11n+Bluetooth 4.0, Gigabit Ethernet, and 4× USB 2.0. The S model adds 16GB eMMC. [Details](https://openhardware.directory/devices/tinkerboard) | [Markdown](https://openhardware.directory/devices/tinkerboard/md) ## Pine64 / LTS Affordable 64-bit Linux SBC by Pine64, powered by the Allwinner A64 SoC with up to 2GB LPDDR3, Gigabit Ethernet, 2× USB 2.0, and microSD — available in standard and Long-Term Support variants. [Details](https://openhardware.directory/devices/pine64) | [Markdown](https://openhardware.directory/devices/pine64/md) ## Libre Computer Tritium H3 Libre Computer Tritium H3 — Allwinner H3 quad-core SBC with 1GB DDR3, 8GB eMMC, 100Mbps Ethernet, and four USB 2.0 ports in a Raspberry Pi 2/3 compatible layout. [Details](https://openhardware.directory/devices/tritium-h3) | [Markdown](https://openhardware.directory/devices/tritium-h3/md) ## Libre Computer Tritium H5 Libre Computer Tritium H5 — Allwinner H5 quad-core 64-bit SBC with 1GB/2GB DDR4, 8GB eMMC, Gigabit Ethernet, and four USB 2.0 ports in a Raspberry Pi-compatible layout. [Details](https://openhardware.directory/devices/tritium-h5) | [Markdown](https://openhardware.directory/devices/tritium-h5/md) ## Radxa NIO 12L Radxa NIO 12L — MediaTek Dimensity 1200 (MT8395) octa-core SBC with 8GB/16GB LPDDR4X, 64GB/128GB eMMC, WiFi 6, Gigabit Ethernet, and USB-C, running Armbian Linux. [Details](https://openhardware.directory/devices/radxa-nio-12l) | [Markdown](https://openhardware.directory/devices/radxa-nio-12l/md) ## JetHub D1 / D1+ DIN-rail mountable Linux IoT hub by JetHome, powered by the Amlogic S905W2 SoC with up to 4GB DDR4, 16GB eMMC, WiFi 5, Bluetooth 5.0, Gigabit Ethernet, and 12V DC — designed for home automation and industrial IoT. [Details](https://openhardware.directory/devices/jethub-d1) | [Markdown](https://openhardware.directory/devices/jethub-d1/md) ## JetHub H1 DIN-rail mountable Linux IoT hub by JetHome, powered by the Amlogic S905W SoC with 2GB DDR4, 8GB eMMC, WiFi 802.11n, Bluetooth 4.0, Gigabit Ethernet, and 12V DC — compact smart home controller for panel installation. [Details](https://openhardware.directory/devices/jethub-h1) | [Markdown](https://openhardware.directory/devices/jethub-h1/md) ## Adafruit PyGamer Handheld gaming console and dev board powered by ATSAMD51J19 (120MHz Cortex-M4F) with a 1.8" TFT display, 5 NeoPixels, accelerometer, and Feather-compatible headers. Runs MakeCode Arcade, CircuitPython, or Arduino. [Details](https://openhardware.directory/devices/adafruit-pygamer) | [Markdown](https://openhardware.directory/devices/adafruit-pygamer/md) ## Adafruit GEMMA M0 Coin-sized wearable microcontroller board with ATSAMD21E18 Cortex M0+ at 48MHz, 3 I/O sew pads, built-in RGB DotStar LED, and CircuitPython pre-installed. Designed for e-textiles and wearable projects. [Details](https://openhardware.directory/devices/adafruit-gemma-m0) | [Markdown](https://openhardware.directory/devices/adafruit-gemma-m0/md) ## Adafruit METRO M0 Express Arduino Uno-compatible development board powered by ATSAMD21G18 Cortex M0+ at 48MHz with 256KB flash, 32KB SRAM, 2MB SPI flash, and CircuitPython pre-loaded. Features Arduino shield compatibility and native USB. [Details](https://openhardware.directory/devices/adafruit-metro-m0-express) | [Markdown](https://openhardware.directory/devices/adafruit-metro-m0-express/md) ## Raspberry Pi 4 Model B Flagship Raspberry Pi SBC with BCM2711 quad-core Cortex-A72 @ 1.5GHz, dual-band WiFi, Gigabit Ethernet, dual micro-HDMI 4K outputs, USB 3.0, and USB-C power. Available in 1GB, 2GB, 4GB, and 8GB LPDDR4 RAM variants. [Details](https://openhardware.directory/devices/raspberry-pi-4-model-b) | [Markdown](https://openhardware.directory/devices/raspberry-pi-4-model-b/md) ## Adafruit HalloWing M4 Express Skull-shaped ATSAMD51J19 dev board (120MHz Cortex-M4F) with a 1.54" 240×240 IPS TFT, 4 capacitive touch inputs, 4 NeoPixels, accelerometer, speaker driver, and LiPoly charging. Perfect for Halloween props and wearables. [Details](https://openhardware.directory/devices/adafruit-hallowing-m4-express) | [Markdown](https://openhardware.directory/devices/adafruit-hallowing-m4-express/md) ## BBC micro:bit v1 Pocket-sized educational microcontroller with nRF51822, 5×5 LED matrix, accelerometer, magnetometer, Bluetooth LE, 2 buttons, and 19 I/O pins. Designed for teaching coding to children and beginners via MakeCode or MicroPython. [Details](https://openhardware.directory/devices/bbc-microbit-v1) | [Markdown](https://openhardware.directory/devices/bbc-microbit-v1/md) ## Circuit Playground Bluefruit Round educational microcontroller with Nordic nRF52840 (64MHz Cortex-M4F + BLE), 10 NeoPixels, accelerometer, microphone, light sensor, speaker, 8 alligator-clip I/O pads, and USB. Runs CircuitPython, MakeCode, and Arduino. [Details](https://openhardware.directory/devices/circuit-playground-bluefruit) | [Markdown](https://openhardware.directory/devices/circuit-playground-bluefruit/md) ## Raspberry Pi 500 The Raspberry Pi 500 is an all-in-one desktop computer built into a compact keyboard, packing a quad-core Cortex-A76 at 2.4GHz, 8GB LPDDR4X RAM, 32GB microSD, dual-band WiFi 5, Bluetooth 5.0, and a 40-pin GPIO header into a single plug-and-go device. [Details](https://openhardware.directory/devices/raspberry-pi-500) | [Markdown](https://openhardware.directory/devices/raspberry-pi-500/md) ## Adafruit Feather STM32F405 Express High-speed Feather-form-factor dev board with STM32F405 ARM Cortex-M4F @ 168MHz, 1MB Flash, 192KB RAM, 2MB SPI Flash, USB-C, STEMMA QT, SD card socket, and LiPo charging. Adafruit's fastest CircuitPython board. [Details](https://openhardware.directory/devices/adafruit-feather-stm32f405-express) | [Markdown](https://openhardware.directory/devices/adafruit-feather-stm32f405-express/md) ## Adafruit PyPortal Titano Large-screen IoT display board with ATSAMD51J20 + ESP32 WiFi coprocessor, 3.5" 320×480 resistive touchscreen TFT, 8MB Flash, microSD, speaker, and USB-C. Designed for Python-powered internet-connected dashboards. [Details](https://openhardware.directory/devices/adafruit-pyportal-titano) | [Markdown](https://openhardware.directory/devices/adafruit-pyportal-titano/md) ## Adafruit ItsyBitsy nRF52840 Express Tiny breadboard-friendly Bluetooth LE board with Nordic nRF52840 Cortex-M4F @ 64MHz, 1MB Flash, 256KB RAM, 2MB QSPI Flash, 21 GPIO, and native USB — all in a 36×17.6mm footprint. Supports CircuitPython and Arduino. [Details](https://openhardware.directory/devices/adafruit-itsybitsy-nrf52840-express) | [Markdown](https://openhardware.directory/devices/adafruit-itsybitsy-nrf52840-express/md) ## Raspberry Pi Zero 2 W Credit-card-tiny Linux SBC with a quad-core Cortex-A53 at 1 GHz, 512 MB RAM, 2.4 GHz WiFi, Bluetooth 4.2, a 40-pin GPIO header footprint, mini HDMI, and a CSI camera connector. [Details](https://openhardware.directory/devices/raspberry-pi-zero-2-w) | [Markdown](https://openhardware.directory/devices/raspberry-pi-zero-2-w/md) ## Adafruit ItsyBitsy 32u4 3V 8MHz Ultra-compact 3.3V Arduino-compatible board with ATmega32u4 at 8MHz, native USB HID, 23 GPIO pins, 2KB RAM, 28KB flash, and Micro USB. Measures 35mm × 17mm — smaller than a Feather with equivalent AVR capability. [Details](https://openhardware.directory/devices/adafruit-itsybitsy-32u4-3v) | [Markdown](https://openhardware.directory/devices/adafruit-itsybitsy-32u4-3v/md) ## Adafruit Feather nRF52840 Sense Sensor-rich BLE Feather with Nordic nRF52840 (64MHz Cortex-M4F), 6 onboard sensors (9-DoF IMU, magnetometer, proximity/light, PDM mic, humidity, barometric pressure), 21 GPIO, and FCC/IC/TELEC certified. [Details](https://openhardware.directory/devices/adafruit-feather-nrf52840-sense) | [Markdown](https://openhardware.directory/devices/adafruit-feather-nrf52840-sense/md) ## Adafruit ItsyBitsy 32u4 5V 16MHz Ultra-compact 5V Arduino-compatible board with ATmega32u4 at 16MHz, native USB HID, 23 GPIO pins, 2KB RAM, 28KB flash, and Micro USB. Measures 35mm × 18mm — small form factor with full Arduino Leonardo capability. [Details](https://openhardware.directory/devices/adafruit-itsybitsy-32u4-5v) | [Markdown](https://openhardware.directory/devices/adafruit-itsybitsy-32u4-5v/md) ## PJRC Teensy 4.1 High-performance microcontroller with NXP i.MX RT1062 ARM Cortex-M7 @ 600MHz, 1MB RAM, 2MB Flash, 100Mbps Ethernet PHY, SD card, 55 GPIO, dual 480Mbps USB, and 3 CAN Bus. Expanded Teensy 4.0 sibling. [Details](https://openhardware.directory/devices/pjrc-teensy-4-1) | [Markdown](https://openhardware.directory/devices/pjrc-teensy-4-1/md) ## Raspberry Pi Zero WH Raspberry Pi Zero W with pre-soldered 40-pin GPIO headers. BCM2835 single-core 1GHz ARM11, 512MB RAM, built-in 802.11 b/g/n WiFi (BCM43143), Bluetooth LE, Mini HDMI, Micro USB, and MicroSD. No soldering required. [Details](https://openhardware.directory/devices/raspberry-pi-zero-wh) | [Markdown](https://openhardware.directory/devices/raspberry-pi-zero-wh/md) ## ESP32-S2-WROVER Module Bare WiFi module with Espressif ESP32-S2 single-core Xtensa LX7 @ 240MHz, 4MB Flash, 2MB PSRAM, 802.11b/g/n, native USB 1.1 OTG, and SMD pads. Intended for integration onto custom PCBs, not a standalone dev board. [Details](https://openhardware.directory/devices/esp32-s2-wrover-module) | [Markdown](https://openhardware.directory/devices/esp32-s2-wrover-module/md) ## Raspberry Pi 500+ The Raspberry Pi 500+ is a premium all-in-one keyboard computer with the Raspberry Pi 5 processor, 16GB LPDDR4X RAM, 256GB internal NVMe SSD, mechanical Gateron KS-33 switches with RGB, dual-band WiFi 5, Bluetooth 5.0, and a 40-pin GPIO header — a complete high-performance desktop in a keyboard. [Details](https://openhardware.directory/devices/raspberry-pi-500-plus) | [Markdown](https://openhardware.directory/devices/raspberry-pi-500-plus/md) ## Adafruit ItsyBitsy M0 Express Compact 3.3V CircuitPython/Arduino board with ATSAMD21G18 Cortex M0+ at 48MHz, 32KB RAM, 256KB flash, 2MB SPI flash, 23 GPIO with 11 analog inputs, RGB DotStar LED, native USB. Measures 36mm × 18mm. [Details](https://openhardware.directory/devices/adafruit-itsybitsy-m0-express) | [Markdown](https://openhardware.directory/devices/adafruit-itsybitsy-m0-express/md) ## ESP32-S2-WROVER-I Module with uFL Bare WiFi module with ESP32-S2 Xtensa LX7 @ 240MHz, 4MB Flash, 2MB PSRAM, 802.11b/g/n, native USB OTG, and a uFL connector for an external antenna. Drop-in variant of the WROVER for improved RF range. [Details](https://openhardware.directory/devices/esp32-s2-wrover-i-module-with-ufl) | [Markdown](https://openhardware.directory/devices/esp32-s2-wrover-i-module-with-ufl/md) ## Adafruit ItsyBitsy M4 Express High-performance compact board with ATSAMD51 Cortex M4F at 120MHz, 192KB RAM, 512KB flash, 2MB SPI flash, dual 12-bit DAC/ADC, 18 PWM outputs, AES-256 crypto, and native USB. Measures 36mm × 18mm. [Details](https://openhardware.directory/devices/adafruit-itsybitsy-m4-express) | [Markdown](https://openhardware.directory/devices/adafruit-itsybitsy-m4-express/md) ## ESP32-S2 Saola 1R Dev Kit Espressif official ESP32-S2-WROVER development board with dual 20-pin headers (breadboard-friendly), 8MB Flash, 2MB PSRAM, WiFi, dual Micro-USB (native USB + UART bridge), NeoPixel RGB LED, and boot/reset buttons. [Details](https://openhardware.directory/devices/esp32-s2-saola-1r-dev-kit) | [Markdown](https://openhardware.directory/devices/esp32-s2-saola-1r-dev-kit/md) ## Adafruit Feather M4 Express High-performance Feather with ATSAMD51J19 Cortex M4F at 120MHz, 192KB RAM, 512KB flash, 2MB SPI flash, dual 12-bit DAC/ADC, AES-256 hardware crypto, LiPo charging, 21 GPIO, and native USB HID. Feather ecosystem compatible. [Details](https://openhardware.directory/devices/adafruit-feather-m4-express) | [Markdown](https://openhardware.directory/devices/adafruit-feather-m4-express/md) ## ESP32-S2 Kaluga Dev Kit Espressif's multimedia-focused ESP32-S2 evaluation platform bundling four extension boards: audio player, capacitive touch panel, 3.2" LCD display, and camera module. Designed to showcase ESP32-S2 human-computer interaction features. [Details](https://openhardware.directory/devices/esp32-s2-kaluga-dev-kit) | [Markdown](https://openhardware.directory/devices/esp32-s2-kaluga-dev-kit/md) ## Adafruit HalloWing M0 Express Skull-shaped wearable microcontroller with ATSAMD21G18 at 48MHz, 1.44" 128x128 TFT display, 3-axis accelerometer, light sensor, 4 capacitive touch pads, 2W speaker driver, 8MB SPI flash, and LiPo charging. [Details](https://openhardware.directory/devices/adafruit-hallowing-m0-express) | [Markdown](https://openhardware.directory/devices/adafruit-hallowing-m0-express/md) ## Adafruit Feather M4 CAN Express CAN-bus-capable Feather with ATSAME51J19 ARM Cortex-M4F @ 120MHz, built-in CAN transceiver + 5V booster, USB-C, 21 GPIO, 2MB SPI Flash, dual DAC, and LiPo charging. Ideal for automotive and industrial CAN Bus projects. [Details](https://openhardware.directory/devices/adafruit-feather-m4-can-express) | [Markdown](https://openhardware.directory/devices/adafruit-feather-m4-can-express/md) ## Adafruit PyBadge LC Low-cost credit card-sized gaming/badge board with ATSAMD51J19 at 120MHz, 1.8\" 160x128 TFT, 8 game buttons, 1 NeoPixel, light sensor, buzzer, 2MB SPI flash, and MicroSD. Supports MakeCode Arcade, CircuitPython, and Arduino. [Details](https://openhardware.directory/devices/adafruit-pybadge-lc) | [Markdown](https://openhardware.directory/devices/adafruit-pybadge-lc/md) ## FeatherS2 ESP32-S2 Full-featured ESP32-S2 Feather-compatible board by Unexpected Maker with 16MB Flash, 8MB QSPI PSRAM, WiFi, native USB-C, 21 GPIO, STEMMA QT, APA102 RGB LED, ambient light sensor, and dual 700mA LDOs. [Details](https://openhardware.directory/devices/feathers2-esp32-s2) | [Markdown](https://openhardware.directory/devices/feathers2-esp32-s2/md) ## Adafruit Metro ESP32-S2 Arduino Uno-compatible WiFi dev board with ESP32-S2 single-core @ 240MHz, 4MB Flash, 2MB PSRAM, native USB-C, STEMMA QT, LiPoly charging, MAX17048 fuel gauge, barrel jack, and UNO shield compatibility. [Details](https://openhardware.directory/devices/adafruit-metro-esp32-s2) | [Markdown](https://openhardware.directory/devices/adafruit-metro-esp32-s2/md) ## BBC micro:bit v2 Upgraded BBC micro:bit with Nordic nRF52833 Cortex-M4F, Bluetooth 5.1, 5×5 LED matrix, 2 buttons, capacitive touch logo, built-in speaker and MEMS microphone, edge connector, and low-power mode. Same form factor as v1. [Details](https://openhardware.directory/devices/bbc-micro-bit-v2) | [Markdown](https://openhardware.directory/devices/bbc-micro-bit-v2/md) ## Adafruit Metro M4 Express AirLift Arduino Uno-compatible board with ATSAMD51J19 Cortex M4F at 120MHz, ESP32 AirLift WiFi co-processor with TLS/SSL, 512KB flash, 192KB RAM, 2MB QSPI flash, 25 GPIO, dual DAC/ADC, and native USB. Arduino shield compatible. [Details](https://openhardware.directory/devices/adafruit-metro-m4-airlift) | [Markdown](https://openhardware.directory/devices/adafruit-metro-m4-airlift/md) ## Raspberry Pi Compute Module 4 Industrial-grade embedded computer module with BCM2711 quad-core Cortex-A72 @ 1.5GHz, 1–8GB LPDDR4 RAM, optional 8–32GB eMMC and optional dual-band WiFi + Bluetooth 5.0. Available in 32 hardware variants on dual high-density connectors. [Details](https://openhardware.directory/devices/raspberry-pi-compute-module-4) | [Markdown](https://openhardware.directory/devices/raspberry-pi-compute-module-4/md) ## Adafruit Feather nRF52840 Express Feather board with nRF52840 ARM Cortex-M4F at 64MHz, BLE 5.0, native USB (CDC/HID/MIDI/MSC), 1MB flash, 256KB SRAM, 2MB QSPI flash, 21 GPIO, SWD debug, and LiPo charging. Supports Arduino and CircuitPython. [Details](https://openhardware.directory/devices/adafruit-feather-nrf52840-express) | [Markdown](https://openhardware.directory/devices/adafruit-feather-nrf52840-express/md) ## Raspberry Pi CM4 IO Board Official reference carrier board for the Raspberry Pi Compute Module 4. Exposes dual HDMI 2.0, Gigabit Ethernet, 2× USB 2.0, PCIe x1, dual camera/display FPC, microSD slot (for CM4 Lite), RTC, HAT headers, and barrel-jack power. [Details](https://openhardware.directory/devices/raspberry-pi-cm4-io-board) | [Markdown](https://openhardware.directory/devices/raspberry-pi-cm4-io-board/md) ## Adafruit Grand Central M4 Express Arduino Mega-form-factor board with ATSAMD51P20 Cortex M4F at 120MHz, 1MB flash, 256KB RAM, 8MB QSPI flash, 70 GPIO pins, SD card slot, 8 SERCOM, 22 PWM outputs, dual DAC/ADC, AES-256, and native USB. [Details](https://openhardware.directory/devices/adafruit-grand-central-m4-express) | [Markdown](https://openhardware.directory/devices/adafruit-grand-central-m4-express/md) ## Adafruit PyBadge Credit card-sized gaming and badge board with ATSAMD51J19 at 120MHz, 1.8\" 160x128 TFT, 8 game buttons, 5 NeoPixels, LIS3DH accelerometer, light sensor, 2W speaker, 2MB SPI flash, Feather headers, STEMMA connectors, and LiPo charging. [Details](https://openhardware.directory/devices/adafruit-pybadge) | [Markdown](https://openhardware.directory/devices/adafruit-pybadge/md) ## Arduino MKR WiFi 1010 Compact IoT Arduino with SAMD21 Cortex-M0+ @ 48MHz, u-blox NINA-W102 WiFi + Bluetooth module, ATECC508 crypto chip, 256KB Flash, 32KB SRAM, USB full-speed, LiPo charging, and MKR shield compatibility. [Details](https://openhardware.directory/devices/arduino-mkr-wifi-1010) | [Markdown](https://openhardware.directory/devices/arduino-mkr-wifi-1010/md) ## Arduino Uno R3 The quintessential beginner microcontroller board with ATmega328P @ 16MHz, 32KB Flash, 2KB SRAM, 14 digital I/O, 6 analog inputs, USB-B for programming, DC barrel jack, and the R3 expanded shield header. Open-source hardware. [Details](https://openhardware.directory/devices/arduino-uno-r3) | [Markdown](https://openhardware.directory/devices/arduino-uno-r3/md) ## Adafruit Feather RP2040 Feather-form-factor board with Raspberry Pi RP2040 dual-core Cortex-M0+ @ 133MHz, 264KB SRAM, 8MB Flash, 21 GPIO, 4 ADC, 2 PIO peripherals, USB-C with UF2 bootloader, STEMMA QT, and LiPo charging. Runs CircuitPython and MicroPython. [Details](https://openhardware.directory/devices/adafruit-feather-rp2040) | [Markdown](https://openhardware.directory/devices/adafruit-feather-rp2040/md) ## Adafruit ItsyBitsy RP2040 Tiny 36×18mm breadboard-friendly board with Raspberry Pi RP2040 dual-core Cortex-M0+ @ 133MHz, 264KB SRAM, 8MB Flash, 23 GPIO, 4 ADC, 2 PIO peripherals, and Micro-USB. Runs CircuitPython and MicroPython. [Details](https://openhardware.directory/devices/adafruit-itsybitsy-rp2040) | [Markdown](https://openhardware.directory/devices/adafruit-itsybitsy-rp2040/md) ## Heltec HT1303 A mini-PCIe LoRaWAN concentrator module based on Semtech SX1303 + SX1250, enabling easy integration of LPWAN gateway capabilities into routers, Raspberry Pi, or other platforms with standard mini-PCIe slots. [Details](https://openhardware.directory/devices/heltec-ht1303) | [Markdown](https://openhardware.directory/devices/heltec-ht1303/md) ## Heltec Sufficient IoT Hub Linux-based IoT hub with Allwinner T113-S3 dual-core ARM Cortex-A7 SoC, LoRa (SX1262), WiFi, Ethernet, and optional LTE. Runs Debian 10 with a dedicated IoT OS, CLI, and web UI for no-code device management. [Details](https://openhardware.directory/devices/heltec-sufficient-iot-hub) | [Markdown](https://openhardware.directory/devices/heltec-sufficient-iot-hub/md) ## M5Stack StamPLC ESP32-S3 industrial PLC controller with 1.14" IPS LCD, 4 relays, 8 opto-isolated inputs, RS-485, CAN bus, INA226 power monitor, RTC, buzzer, microSD, and DIN-rail mounting in a compact enclosure. [Details](https://openhardware.directory/devices/m5stack-stamplc) | [Markdown](https://openhardware.directory/devices/m5stack-stamplc/md) ## Heltec MeshPocket Qi2 magnetic wireless charging power bank with integrated Meshtastic mesh networking node, featuring nRF52840 BLE + SX1262 LoRa radio and a 2.13" e-ink display. Available in 5000mAh and 10000mAh configurations. [Details](https://openhardware.directory/devices/heltec-meshpocket) | [Markdown](https://openhardware.directory/devices/heltec-meshpocket/md) ## Heltec Vision Master T190 ESP32-S3 development board with optional SX1262 LoRa module and 1.9-inch TFT color display. Supports Meshtastic, LoRaWAN, Arduino, MicroPython, and features integrated battery management with 18uA deep sleep. [Details](https://openhardware.directory/devices/heltec-vision-master-t190) | [Markdown](https://openhardware.directory/devices/heltec-vision-master-t190/md) ## BeagleBone Black Industrial Industrial-rated BeagleBone Black with extended temperature range (-40°C to +85°C), TI Sitara AM3358 ARM Cortex-A8 at 1 GHz, full cape and software compatibility, for harsh environment deployments. [Details](https://openhardware.directory/devices/beaglebone-black-industrial) | [Markdown](https://openhardware.directory/devices/beaglebone-black-industrial/md) ## Arduino UNO R4 WiFi Arduino's flagship UNO board upgraded with Renesas RA4M1 ARM Cortex-M4F at 48MHz, ESP32-S3 WiFi/BLE 5.0, built-in 12×8 LED matrix, 12-bit DAC, CAN bus, op-amp, and Qwiic connector — all in the classic UNO form factor at 5V. [Details](https://openhardware.directory/devices/arduino-uno-r4-wifi) | [Markdown](https://openhardware.directory/devices/arduino-uno-r4-wifi/md) ## Arduino UNO R4 Minima The affordable entry to Arduino's R4 generation — Renesas RA4M1 ARM Cortex-M4F at 48MHz with 256KB flash, 32KB SRAM, 12-bit DAC, CAN bus, op-amp, and USB-C in the classic UNO form factor at 5V. No wireless, pure microcontroller power. [Details](https://openhardware.directory/devices/arduino-uno-r4-minima) | [Markdown](https://openhardware.directory/devices/arduino-uno-r4-minima/md) ## Arduino Nano ESP32 Arduino Nano form factor powered by ESP32-S3 with WiFi 802.11 b/g/n, Bluetooth LE 5.0, dual-core Xtensa LX7 at 240MHz, 8MB flash, 512KB SRAM, USB-C, and HID support — Arduino's compact IoT powerhouse with MicroPython support. [Details](https://openhardware.directory/devices/arduino-nano-esp32) | [Markdown](https://openhardware.directory/devices/arduino-nano-esp32/md) ## Arduino Nano Every Compact 45×18mm Arduino Nano with ATMega4809 at 20MHz — 48KB flash, 6KB SRAM, 5V logic, 14 digital I/O (5 PWM), 8 analog inputs, and USB-C. A modern, affordable 8-bit board for embedded projects and breadboard prototyping. [Details](https://openhardware.directory/devices/arduino-nano-every) | [Markdown](https://openhardware.directory/devices/arduino-nano-every/md) ## Arduino GIGA R1 WiFi Arduino's most powerful board — dual-core STM32H747XI with Cortex-M7 at 480MHz + Cortex-M4 at 240MHz, 2MB flash, 1MB RAM, WiFi, Bluetooth, 76 GPIO, USB-A + USB-C, 3.5mm audio jack, camera connector, and CAN bus in Mega/Due form factor. [Details](https://openhardware.directory/devices/arduino-giga-r1-wifi) | [Markdown](https://openhardware.directory/devices/arduino-giga-r1-wifi/md) ## Arduino Nano 33 BLE Sense Rev2 Sensor-packed Nano board with nRF52840 ARM Cortex-M4F at 64MHz, BLE 5.0, 9-axis IMU, microphone, temperature, humidity, pressure, light, and gesture sensors — designed for TinyML and edge AI projects in a 45×18mm form factor. [Details](https://openhardware.directory/devices/arduino-nano-33-ble-sense-rev2) | [Markdown](https://openhardware.directory/devices/arduino-nano-33-ble-sense-rev2/md) ## Arduino Nano RP2040 Connect Nano form factor board with RP2040 dual-core Cortex-M0+ at 133MHz, 16MB flash, 264KB SRAM, WiFi 802.11 b/g/n and BLE via u-blox NINA-W102, built-in 6-axis IMU and microphone, 22 digital I/O with 20 PWM channels. [Details](https://openhardware.directory/devices/arduino-nano-rp2040-connect) | [Markdown](https://openhardware.directory/devices/arduino-nano-rp2040-connect/md) ## Arduino Nano R4 The newest Arduino Nano — Renesas RA4M1 ARM Cortex-M4F at 48MHz with 256KB flash, 32KB SRAM, Qwiic connector, RGB LED, castellated pins, and USB-C in an ultra-compact 43×17mm form factor. No wireless, pure embedded power. [Details](https://openhardware.directory/devices/arduino-nano-r4) | [Markdown](https://openhardware.directory/devices/arduino-nano-r4/md) ## Arduino UNO Q Arduino's first Linux-capable UNO — Qualcomm Dragonwing QRB2210 quad-core Cortex-A53 + STM32U585 real-time co-processor, 2GB/4GB RAM, 16GB eMMC, WiFi 5, Bluetooth 5.1, 8×13 LED matrix, USB-C, and AI-ready with Arduino App Lab in the classic UNO form factor. [Details](https://openhardware.directory/devices/arduino-uno-q) | [Markdown](https://openhardware.directory/devices/arduino-uno-q/md) ## Arduino Uno Rev3 The original Arduino UNO — the world's most popular development board with ATmega328P at 16MHz, 32KB flash, 2KB SRAM, 14 digital I/O (6 PWM), 6 analog inputs, USB-B, and 5V operation. The gateway to electronics and programming for millions. [Details](https://openhardware.directory/devices/arduino-uno-rev3) | [Markdown](https://openhardware.directory/devices/arduino-uno-rev3/md) ## Arduino Nano The classic breadboard-friendly Arduino — ATmega328P at 16MHz, 32KB flash, 2KB SRAM, 14 digital I/O (6 PWM), 8 analog inputs, Mini-B USB, and 5V operation in a tiny 45×18mm form factor. The compact original. [Details](https://openhardware.directory/devices/arduino-nano) | [Markdown](https://openhardware.directory/devices/arduino-nano/md) ## Arduino Stella Arduino's Ultra-Wideband (UWB) board with nRF52840 ARM Cortex-M4F, Truesense DCU040 UWB module, BLE 5.0, and NFC — enabling centimeter-accurate indoor positioning, asset tracking, and secure proximity interactions. [Details](https://openhardware.directory/devices/arduino-stella) | [Markdown](https://openhardware.directory/devices/arduino-stella/md) ## Arduino MKR WAN 1310 LoRa-enabled IoT board with SAMD21 ARM Cortex-M0+ at 48MHz, Murata CMWX1ZZABZ LoRa module, ECC508 crypto chip, 2MB SPI flash, onboard LiPo charger, and 104\u00b5A low-power mode — designed for long-range, battery-powered IoT sensor networks. [Details](https://openhardware.directory/devices/arduino-mkr-wan-1310) | [Markdown](https://openhardware.directory/devices/arduino-mkr-wan-1310/md) ## Arduino Opta WiFi Industrial micro PLC with STM32H747 dual-core Cortex-M7/M4, WiFi, BLE, Ethernet, 4\u00d72.3kW relays, Modbus TCP/RTU, hardware security, DIN rail mount, and IEC 61131-3 PLC programming — co-developed with Finder for real industrial automation. [Details](https://openhardware.directory/devices/arduino-opta-wifi) | [Markdown](https://openhardware.directory/devices/arduino-opta-wifi/md) ## Arduino Opta Lite Entry-level industrial micro PLC with STM32H747 dual-core Cortex-M7/M4, Ethernet, 4\u00d72.3kW relays, Modbus TCP, hardware security, DIN rail mount, and IEC 61131-3 PLC programming — the affordable path to Arduino-powered industrial control. [Details](https://openhardware.directory/devices/arduino-opta-lite) | [Markdown](https://openhardware.directory/devices/arduino-opta-lite/md) ## NanoPC-T6 Plus FriendlyElec's flagship RK3588 SBC with 4x Cortex-A76 + 4x Cortex-A53 at 2.4GHz, up to 32GB LPDDR5, NVMe M.2, dual 2.5GbE, dual HDMI out + HDMI in, 6 TOPS NPU, 8K video, 40-pin GPIO, and USB-C PD power. [Details](https://openhardware.directory/devices/nanopc-t6-plus) | [Markdown](https://openhardware.directory/devices/nanopc-t6-plus/md) ## NanoPi R6S High-performance RK3588S router board with 8GB LPDDR4X, 32GB eMMC, native Gigabit + dual 2.5GbE, HDMI 2.1 (8K), USB 3.0, and 6 TOPS NPU — ideal for OpenWrt/FriendlyWrt router, NAS, and edge computing. [Details](https://openhardware.directory/devices/nanopi-r6s) | [Markdown](https://openhardware.directory/devices/nanopi-r6s/md) ## NanoPi M5 Mid-range RK3576 SBC with 4x Cortex-A72 + 4x Cortex-A53 at 2.2GHz, up to 8GB RAM, dual Gigabit Ethernet, M.2 NVMe, HDMI 4K, 6 TOPS NPU, MIPI-CSI/DSI, 30-pin GPIO, and USB-C PD in a compact 90×62mm form factor. [Details](https://openhardware.directory/devices/nanopi-m5) | [Markdown](https://openhardware.directory/devices/nanopi-m5/md) ## NanoPi R4S Popular RK3399 dual-GbE router board with 2x Cortex-A72 + 4x Cortex-A53, 4GB LPDDR4, dual Gigabit Ethernet, 2x USB 3.0, metal case option, and OpenWrt/FriendlyWrt support — the go-to affordable open-source router platform. [Details](https://openhardware.directory/devices/nanopi-r4s) | [Markdown](https://openhardware.directory/devices/nanopi-r4s/md) ## NanoPi R2S Budget dual-GbE router board with RK3328 quad-core Cortex-A53 at 1.3GHz, 1GB DDR4, native + USB 3.0 Gigabit Ethernet, and USB-C power — the most affordable open-source OpenWrt router platform at just $27. [Details](https://openhardware.directory/devices/nanopi-r2s) | [Markdown](https://openhardware.directory/devices/nanopi-r2s/md) ## BigTreeTech SKR Pro V1.1 32-bit 3D printer control board powered by STM32F407ZGT6 @ 168MHz. Supports 6 stepper drivers, triple extruder, dual Z, 12–24V input. Compatible with Marlin and Klipper firmware. [Details](https://openhardware.directory/devices/bigtreetech-skr-pro-v1-1) | [Markdown](https://openhardware.directory/devices/bigtreetech-skr-pro-v1-1/md) ## NanoPi Zero2 Ultra-compact 45\u00d745mm Linux SBC with RK3528A quad-core Cortex-A53 at 1.8GHz, up to 2GB RAM, Gigabit Ethernet, M.2 WiFi slot, USB 2.0, 30-pin GPIO, and 4K HDMI — starting at just $18. [Details](https://openhardware.directory/devices/nanopi-zero2) | [Markdown](https://openhardware.directory/devices/nanopi-zero2/md) ## BigTreeTech SKR V1.4 Turbo 32-bit 3D printer control board with LPC1769 @ 120MHz. Supports 5 stepper driver sockets, dual Z, 12–24V, TMC2209 UART. Popular Marlin and Klipper compatible upgrade board. [Details](https://openhardware.directory/devices/bigtreetech-skr-v1-4-turbo) | [Markdown](https://openhardware.directory/devices/bigtreetech-skr-v1-4-turbo/md) ## BigTreeTech SKR Mini E3 V1.2 Ultra-quiet 32-bit 3D printer board with 4 integrated TMC2209 UART stepper drivers. STM32F103RCT6 @ 72MHz. Direct drop-in replacement for Ender 3. Supports Marlin and Klipper. [Details](https://openhardware.directory/devices/bigtreetech-skr-mini-e3-v1-2) | [Markdown](https://openhardware.directory/devices/bigtreetech-skr-mini-e3-v1-2/md) ## BigTreeTech SKR Mini E3 V2.0 Improved 32-bit control board with 4 integrated TMC2209 UART drivers, dual Z ports, and STM32F103RCT6 @ 72MHz. Drop-in upgrade for Ender 3, CR-10S, Ender 5. Marlin and Klipper ready. [Details](https://openhardware.directory/devices/bigtreetech-skr-mini-e3-v2-0) | [Markdown](https://openhardware.directory/devices/bigtreetech-skr-mini-e3-v2-0/md) ## BigTreeTech SKR Mini E3 V3.0 Latest 32-bit SKR Mini E3 with STM32G0B1RET6 @ 64MHz, 4 integrated TMC2209 UART drivers, USB-C, and CAN bus support. Compact Ender 3 drop-in upgrade. Marlin and Klipper compatible. [Details](https://openhardware.directory/devices/bigtreetech-skr-mini-e3-v3-0) | [Markdown](https://openhardware.directory/devices/bigtreetech-skr-mini-e3-v3-0/md) ## NanoPi R5S-LTS RK3568B2 router board with quad-core Cortex-A55 at 2.0GHz, up to 4GB RAM, 32GB eMMC, native GbE + dual 2.5GbE, M.2 PCIe, 2x USB 3.0, HDMI 4K, and USB-C PD — the mid-range OpenWrt router with long-term support. [Details](https://openhardware.directory/devices/nanopi-r5s-lts) | [Markdown](https://openhardware.directory/devices/nanopi-r5s-lts/md) ## BigTreeTech BTT Pi V1.2 Single board computer by BigTreeTech with Allwinner H616 quad-core Cortex-A53, 1GB DDR3L RAM, WiFi, 100Mbps Ethernet, and 40-pin GPIO. Drop-in Raspberry Pi CM4 alternative for Klipper 3D printing. [Details](https://openhardware.directory/devices/bigtreetech-btt-pi-v1-2) | [Markdown](https://openhardware.directory/devices/bigtreetech-btt-pi-v1-2/md) ## BigTreeTech SKR Pico V1.0 Compact 32-bit 3D printer control board powered by RP2040 @ 133MHz. Designed for Voron 0.1 and small printers. 4 TMC2209 sockets, USB-C, 12–24V input. Klipper and Marlin compatible. [Details](https://openhardware.directory/devices/bigtreetech-skr-pico-v1-0) | [Markdown](https://openhardware.directory/devices/bigtreetech-skr-pico-v1-0/md) ## NanoPi R5C Compact dual 2.5GbE router with RK3568B2 quad-core Cortex-A55 at 2.0GHz, up to 4GB RAM, dual USB 3.2, HDMI, M.2, and 0.8 TOPS NPU in a tiny 58\u00d758mm form factor — the small-footprint 2.5G OpenWrt router. [Details](https://openhardware.directory/devices/nanopi-r5c) | [Markdown](https://openhardware.directory/devices/nanopi-r5c/md) ## NanoPi R6C RK3588S router board with 4x Cortex-A76 + 4x Cortex-A53, up to 8GB RAM, 32GB eMMC, native GbE + 2.5GbE, M.2 NVMe, HDMI 8K, 6 TOPS NPU, and USB-C PD — the mid-range RK3588S router with NVMe storage support. [Details](https://openhardware.directory/devices/nanopi-r6c) | [Markdown](https://openhardware.directory/devices/nanopi-r6c/md) ## BigTreeTech CB2 Compute module by BigTreeTech powered by Rockchip RK3566 quad-core Cortex-A55 at 1.8GHz, 2GB/4GB LPDDR4, 32GB eMMC, Gigabit Ethernet, WiFi 5 (802.11ac), and Bluetooth 5.2. CM4-form-factor. [Details](https://openhardware.directory/devices/bigtreetech-cb2) | [Markdown](https://openhardware.directory/devices/bigtreetech-cb2/md) ## BigTreeTech SKR 3 High-performance 32-bit 3D printer board with STM32H743VI @ 480MHz, 5 driver slots, CAN bus, FDCAN, WiFi module support, 12–24V, 10A bed output. Marlin, Klipper, and RepRapFirmware compatible. [Details](https://openhardware.directory/devices/bigtreetech-skr-3) | [Markdown](https://openhardware.directory/devices/bigtreetech-skr-3/md) ## BigTreeTech Octopus V1.1 32-bit 3D printer control board with STM32F446ZET6 MCU, 8 stepper driver slots (9 outputs), CAN bus via RJ11, USB-C, WiFi header, and support for Marlin and Klipper firmware. [Details](https://openhardware.directory/devices/bigtreetech-octopus-v1-1) | [Markdown](https://openhardware.directory/devices/bigtreetech-octopus-v1-1/md) ## NanoPC-T6 LTS Long-term support RK3588 SBC with 4x Cortex-A76 + 4x Cortex-A53 at 2.4GHz, up to 16GB LPDDR4X, NVMe PCIe 3.0 x4, dual 2.5GbE, dual HDMI, MIPI-CSI/DSI, 6 TOPS NPU, and 40-pin GPIO — the LTS variant for production deployments. [Details](https://openhardware.directory/devices/nanopc-t6-lts) | [Markdown](https://openhardware.directory/devices/nanopc-t6-lts/md) ## BigTreeTech SKR 3 EZ Advanced 32-bit 3D printer board with STM32H743VI @ 480MHz and EZ driver system (tool-free). 5 EZ driver slots, CAN/FDCAN, WiFi module support, 10A bed, 12–24V. Marlin, Klipper, RRF ready. [Details](https://openhardware.directory/devices/bigtreetech-skr-3-ez) | [Markdown](https://openhardware.directory/devices/bigtreetech-skr-3-ez/md) ## BigTreeTech PAD 7 7-inch all-in-one 3D printer control panel with 1024x600 IPS touchscreen, pre-installed CB1 core board running Klipper, Ethernet, WiFi, 3x USB 2.0, CAN bus, and built-in speaker. [Details](https://openhardware.directory/devices/bigtreetech-pad-7) | [Markdown](https://openhardware.directory/devices/bigtreetech-pad-7/md) ## BigTreeTech Octopus Pro V1.1 High-voltage 3D printer control board with STM32H723ZE MCU, 8 stepper driver slots supporting up to 60V motor power, CAN bus, PT100/PT1000 support, and Marlin/Klipper/RRF firmware. [Details](https://openhardware.directory/devices/bigtreetech-octopus-pro-v1-1) | [Markdown](https://openhardware.directory/devices/bigtreetech-octopus-pro-v1-1/md) ## BigTreeTech Octopus Max EZ V1.0 High-end 32-bit 3D printer control board with STM32H723ZET6 MCU at 550MHz, 10 EZ-socket stepper driver slots, CAN bus, eFuse protection, and Marlin/Klipper firmware support. [Details](https://openhardware.directory/devices/bigtreetech-octopus-max-ez-v1-0) | [Markdown](https://openhardware.directory/devices/bigtreetech-octopus-max-ez-v1-0/md) ## BigTreeTech TFT35 V3.0 3.5-inch dual-mode 3D printer display with STM32 processor supporting both touchscreen TFT mode and classic 12864 LCD mode. Compatible with Marlin and most BIGTREETECH control boards. [Details](https://openhardware.directory/devices/bigtreetech-tft35-v3-0) | [Markdown](https://openhardware.directory/devices/bigtreetech-tft35-v3-0/md) ## NanoPi M6 RK3588S SBC with 4x Cortex-A76 + 4x Cortex-A53 at 2.4GHz, up to 32GB LPDDR5, M.2 NVMe, Gigabit Ethernet, HDMI 2.1 (8K), dual MIPI-DSI/CSI, 6 TOPS NPU, and USB-C PD — FriendlyElec's compact RK3588S desktop-class board. [Details](https://openhardware.directory/devices/nanopi-m6) | [Markdown](https://openhardware.directory/devices/nanopi-m6/md) ## BigTreeTech Manta M4P V1.0 Klipper-native 3D printer control board with STM32G0B0RE MCU and BTB connector for Raspberry Pi CM4 or BTT CB1, 4 stepper driver slots, Ethernet, USB-C, and CAN bus support. [Details](https://openhardware.directory/devices/bigtreetech-manta-m4p-v1-0) | [Markdown](https://openhardware.directory/devices/bigtreetech-manta-m4p-v1-0/md) ## BigTreeTech TFT35-E3 V3.0 3.5-inch dual-mode display designed as a direct replacement for the Ender 3 stock LCD. STM32 based with touchscreen TFT and 12864 emulation modes, supports SD and USB printing. [Details](https://openhardware.directory/devices/bigtreetech-tft35-e3-v3-0) | [Markdown](https://openhardware.directory/devices/bigtreetech-tft35-e3-v3-0/md) ## NanoPi R2S Plus Enhanced RK3328 dual-GbE router with quad-core Cortex-A53 at 1.4GHz, 1GB DDR4, 32GB eMMC onboard, dual Gigabit Ethernet, optional WiFi, and metal case — the R2S upgrade with built-in storage for reliable OpenWrt routing. [Details](https://openhardware.directory/devices/nanopi-r2s-plus) | [Markdown](https://openhardware.directory/devices/nanopi-r2s-plus/md) ## BigTreeTech Manta M8P V1.1 8-axis Klipper-native 3D printer control board with STM32G0B1VET6 MCU, BTB connector for CM4/CB1, CAN bus, eFuse protection, Ethernet, and selectable CNC fan voltage. [Details](https://openhardware.directory/devices/bigtreetech-manta-m8p-v1-1) | [Markdown](https://openhardware.directory/devices/bigtreetech-manta-m8p-v1-1/md) ## BigTreeTech TFT43/TFT50/TFT70 V3.0 Larger-format dual-mode 3D printer displays in 4.3-inch, 5-inch, and 7-inch variants. STM32-based with touchscreen TFT and 12864 LCD emulation modes, SD/USB printing, compatible with Marlin. [Details](https://openhardware.directory/devices/bigtreetech-tft43-tft50-tft70-v3-0) | [Markdown](https://openhardware.directory/devices/bigtreetech-tft43-tft50-tft70-v3-0/md) ## BigTreeTech Manta E3EZ V1.0 Klipper-ready 3D printer control board for Ender 3/5 with STM32G0B1 MCU, BTB connector for CM4/CB1, 5 EZ stepper slots, CAN bus, and direct Ender 3 compatibility. [Details](https://openhardware.directory/devices/bigtreetech-manta-e3ez-v1-0) | [Markdown](https://openhardware.directory/devices/bigtreetech-manta-e3ez-v1-0/md) ## BigTreeTech TFT35-SPI V2.1 3.5-inch 480x320 SPI touchscreen display for 3D printers, designed for CB1-based boards. Uses ILI9488 SPI LCD driver and NS2009 I2C touch controller, includes an IO2CAN module option. [Details](https://openhardware.directory/devices/bigtreetech-tft35-spi-v2-1) | [Markdown](https://openhardware.directory/devices/bigtreetech-tft35-spi-v2-1/md) ## BigTreeTech SKRat V1.0 Compact 32-bit 3D printer control board with STM32G0B1VET6 MCU, 5 stepper driver slots, CAN-FD bus, USB-C, and support for both Marlin and Klipper firmware. [Details](https://openhardware.directory/devices/bigtreetech-skrat-v1-0) | [Markdown](https://openhardware.directory/devices/bigtreetech-skrat-v1-0/md) ## BIQU RGBDuino UNO V1.2 Arduino UNO-compatible development board based on ATmega328P-AU at 16MHz/5V, featuring RGB LED indicators. Available in Geek Duck (V1.1) and Jenny (V1.2) variants for maker and education projects. [Details](https://openhardware.directory/devices/biqu-rgbduino-uno-v1-2) | [Markdown](https://openhardware.directory/devices/biqu-rgbduino-uno-v1-2/md) ## BigTreeTech Pi TFT43 V2.0 4.3-inch 800x480 IPS capacitive touchscreen expansion board for BTT Pi, CB1, CB2, and Raspberry Pi CM4. Connects via 40-pin GPIO DPI interface with GT911 touch controller for Klipper UI. [Details](https://openhardware.directory/devices/bigtreetech-pi-tft43-v2-0) | [Markdown](https://openhardware.directory/devices/bigtreetech-pi-tft43-v2-0/md) ## BigTreeTech ESP8266 WiFi Module ESP8266-based WiFi transceiver expansion module for BTT 3D printer control boards. Available in ESP12S and ESP-07 variants, enabling wireless connectivity and remote control via serial UART. [Details](https://openhardware.directory/devices/bigtreetech-esp8266-wifi-module) | [Markdown](https://openhardware.directory/devices/bigtreetech-esp8266-wifi-module/md) ## BigTreeTech HDMI5 V1.0 5-inch 800x480 IPS HDMI capacitive touchscreen display. Compatible with Raspberry Pi, BTT SBCs, and any HDMI source. USB-C data port, 3.5mm audio jack, 5-point touch, auto-driver on PC. [Details](https://openhardware.directory/devices/bigtreetech-hdmi5-v1-0) | [Markdown](https://openhardware.directory/devices/bigtreetech-hdmi5-v1-0/md) ## CompuLab IOT-GATE-IMX8PLUS Industrial IoT edge gateway with NXP i.MX8M Plus quad-core Cortex-A53 at 1.8GHz, up to 8GB RAM, dual Ethernet (PoE), WiFi/BT, optional 4G LTE, 3x RS485/RS232, USB 3.0, TPM, and modular I/O expansion — designed for industrial-grade edge computing. [Details](https://openhardware.directory/devices/compulab-iot-gate-imx8plus) | [Markdown](https://openhardware.directory/devices/compulab-iot-gate-imx8plus/md) ## BigTreeTech HDMI7 V1.0 7-inch 1024x600 IPS HDMI capacitive touchscreen display. Universal compatibility with Raspberry Pi, BTT SBCs, and any HDMI source. USB-C touch, 3.5mm audio output, 5-point touch, 160° viewing angle. [Details](https://openhardware.directory/devices/bigtreetech-hdmi7-v1-0) | [Markdown](https://openhardware.directory/devices/bigtreetech-hdmi7-v1-0/md) ## BigTreeTech S42C V1.0 Closed Loop Stepper Driver NEMA 17 (42mm) stepper motor closed-loop driver board with OLED display. Uses encoder feedback to eliminate missed steps and improve high-speed 3D printer and CNC motor performance. [Details](https://openhardware.directory/devices/bigtreetech-s42c-v1-0-closed-loop-stepper-driver) | [Markdown](https://openhardware.directory/devices/bigtreetech-s42c-v1-0-closed-loop-stepper-driver/md) ## BigTreeTech EBB 36/42 CAN Bus Toolhead Board CAN bus toolhead board for 36/42mm stepper extruders. Features STM32G0B1 MCU, onboard TMC2209, ADXL345 accelerometer, PT100/PT1000 support, and USB/CAN connectivity for Klipper 3D printers. [Details](https://openhardware.directory/devices/bigtreetech-ebb-36-42-can-bus-toolhead-board) | [Markdown](https://openhardware.directory/devices/bigtreetech-ebb-36-42-can-bus-toolhead-board/md) ## CompuLab IOT-DIN-IMX8PLUS DIN-rail industrial IoT gateway with NXP i.MX8M Plus quad-core Cortex-A53 at 1.8GHz, up to 8GB RAM, dual LAN, CAN bus, RS485/RS232, optional LTE, stackable I/O modules (up to 12x serial, 32x DI/DO, ADC), and 15-year availability. [Details](https://openhardware.directory/devices/compulab-iot-din-imx8plus) | [Markdown](https://openhardware.directory/devices/compulab-iot-din-imx8plus/md) ## BigTreeTech Panda Touch 5-inch 800x480 IPS WiFi touchscreen for Bambu Lab X1, P1, and A1 series 3D printers. ESP32-S3 based, 16MB flash, 8MB PSRAM, built-in battery for portable use, supports up to 4 printers simultaneously. [Details](https://openhardware.directory/devices/bigtreetech-panda-touch) | [Markdown](https://openhardware.directory/devices/bigtreetech-panda-touch/md) ## BigTreeTech ADXL345 V2.0 Accelerometer Board RP2040-based ADXL345 accelerometer board for Klipper input shaping and resonance compensation on 3D printers. Connects via USB Type-C with ESD protection. Board size: 33.25 × 15.5mm. [Details](https://openhardware.directory/devices/bigtreetech-adxl345-v2-0-accelerometer-board) | [Markdown](https://openhardware.directory/devices/bigtreetech-adxl345-v2-0-accelerometer-board/md) ## BigTreeTech EBB SB2209 CAN Toolhead Board (RP2040) Toolhead board designed for the Voron StealthBurner. Powered by RP2040, supports CAN and USB, includes TMC2209, ADXL345 accelerometer, and PT100/PT1000 for Klipper 3D printers. [Details](https://openhardware.directory/devices/bigtreetech-ebb-sb2209-can-toolhead-board-rp2040) | [Markdown](https://openhardware.directory/devices/bigtreetech-ebb-sb2209-can-toolhead-board-rp2040/md) ## BigTreeTech K-Touch 5-inch 800x480 IPS WiFi touchscreen controller for Klipper printers. ESP32-S3 based, 16MB flash, 8MB PSRAM, built-in battery for 30 minutes portable use, supports up to 50 Klipper printers. [Details](https://openhardware.directory/devices/bigtreetech-k-touch) | [Markdown](https://openhardware.directory/devices/bigtreetech-k-touch/md) ## BigTreeTech MicroProbe V2.0 Compact automatic bed leveling probe for 3D printers including Ender-3, B1, and H2 extruder platforms. Supports Voron Stealthburner, EVA, and other popular toolhead mounts. Open source hardware. [Details](https://openhardware.directory/devices/bigtreetech-microprobe-v2-0) | [Markdown](https://openhardware.directory/devices/bigtreetech-microprobe-v2-0/md) ## BigTreeTech MMB CAN V2.0 Multi-Material Control Board CAN bus control board for the Enraged Rabbit Carrot Feeder (ERCF) multi-material system. Features STM32G0B1 MCU, 4 EZ stepper driver slots, USB/CAN connectivity, and full Klipper support. [Details](https://openhardware.directory/devices/bigtreetech-mmb-can-v2-0-multi-material-control-board) | [Markdown](https://openhardware.directory/devices/bigtreetech-mmb-can-v2-0-multi-material-control-board/md) ## BigTreeTech KNOMI 2 1.28-inch round 240x240 LCD display for Voron StealthBurner toolhead. ESP32 MCU with WiFi and Bluetooth LE, shows print status, temperatures, and progress with customizable animated UI. [Details](https://openhardware.directory/devices/bigtreetech-knomi-2) | [Markdown](https://openhardware.directory/devices/bigtreetech-knomi-2/md) ## BigTreeTech BTT RRF WiFi V1.0 Module ESP8266-based WiFi expansion module for RepRapFirmware (Duet-style) boards. Adds wireless connectivity to BTT SKR V1.3, SKR V1.4 Turbo, and compatible boards running RRF or Marlin firmware. [Details](https://openhardware.directory/devices/bigtreetech-btt-rrf-wifi-v1-0-module) | [Markdown](https://openhardware.directory/devices/bigtreetech-btt-rrf-wifi-v1-0-module/md) ## BigTreeTech Eddy Eddy Current Inductive Probe Eddy current inductive bed leveling probe for Klipper 3D printers. Offers 0.5μm precision, rapid bed mesh scanning, temperature compensation (USB), and works as Z-endstop. Mounts on standard Voron X carriage. [Details](https://openhardware.directory/devices/bigtreetech-eddy-eddy-current-inductive-probe) | [Markdown](https://openhardware.directory/devices/bigtreetech-eddy-eddy-current-inductive-probe/md) ## BigTreeTech Panda Knomi 1.28-inch round 240x240 display for Bambu Lab A1, X1, and P1 series printers. ESP32 MCU with 2.4GHz WiFi, customizable GIF animations, shows print status and temperatures wirelessly. [Details](https://openhardware.directory/devices/bigtreetech-panda-knomi) | [Markdown](https://openhardware.directory/devices/bigtreetech-panda-knomi/md) ## BigTreeTech Panda Branch V1.0 USB power expansion board for Bambu Lab X1/P1/A1 series printers. Provides 4x USB-A 5V outputs at up to 2.7A peak from a 24V input, with overcurrent protection and MX3.0 AMS power interfaces. [Details](https://openhardware.directory/devices/bigtreetech-panda-branch-v1-0) | [Markdown](https://openhardware.directory/devices/bigtreetech-panda-branch-v1-0/md) ## BigTreeTech SKSM V1.0 Supercapacitor Power Module Supercapacitor-based power loss recovery module for Klipper 3D printers. Provides ~13 seconds of 5W backup power via dual 2.7V 20F supercaps, enabling safe shutdown on power failure. [Details](https://openhardware.directory/devices/bigtreetech-sksm-v1-0-supercapacitor-power-module) | [Markdown](https://openhardware.directory/devices/bigtreetech-sksm-v1-0-supercapacitor-power-module/md) ## BigTreeTech CEB CAN Expansion Board CAN bus power distribution and expansion board for BigTreeTech toolhead boards. Provides multiple 24V + CAN pass-through ports to daisy-chain toolhead boards in Klipper 3D printer setups. [Details](https://openhardware.directory/devices/bigtreetech-ceb-can-expansion-board) | [Markdown](https://openhardware.directory/devices/bigtreetech-ceb-can-expansion-board/md) ## BigTreeTech Panda PWR Intelligent power management module with ESP8684 MCU, 4MB flash, 2.4GHz WiFi, and dual USB outputs. Enables remote power control, consumption monitoring, countdown shutdown, and Home Assistant integration. [Details](https://openhardware.directory/devices/bigtreetech-panda-pwr) | [Markdown](https://openhardware.directory/devices/bigtreetech-panda-pwr/md) ## BigTreeTech HBB Handheld Button Board RP2040-based handheld button board with 7 mechanical switches and RGB NeoPixel LEDs for manual control of Klipper 3D printers. Triggers homing, heating, motor disable and other macros via USB. [Details](https://openhardware.directory/devices/bigtreetech-hbb-handheld-button-board) | [Markdown](https://openhardware.directory/devices/bigtreetech-hbb-handheld-button-board/md) ## BigTreeTech K-Hub V1.0 4-port USB 2.0 hub for Klipper-based 3D printers with dual 24V/5V power input support. Expands a single USB host port to connect multiple peripherals like ADXL345, EBB boards, and cameras simultaneously. [Details](https://openhardware.directory/devices/bigtreetech-k-hub-v1-0) | [Markdown](https://openhardware.directory/devices/bigtreetech-k-hub-v1-0/md) ## BigTreeTech Rodent V1.0 ESP32-based CNC controller board co-developed with RatRig, featuring 4x TMC2160 drivers (up to 56V/4.7A RMS), FluidNC firmware, WiFi, RS-485, CAN, USB-C, and OLED display support for engraving machines. [Details](https://openhardware.directory/devices/bigtreetech-rodent-v1-0) | [Markdown](https://openhardware.directory/devices/bigtreetech-rodent-v1-0/md) ## BigTreeTech Scylla V1.0 STM32H723-based CNC engraving machine control board with 4x TMC2160 drivers (24-56V/4.7A RMS), RepRapFirmware support, ESP32 WiFi, USB-C, RS-485, CAN bus, VFD spindle control, and relay output. [Details](https://openhardware.directory/devices/bigtreetech-scylla-v1-0) | [Markdown](https://openhardware.directory/devices/bigtreetech-scylla-v1-0/md) ## BIQU AJAX TD1S Filament Transmission Distance (TD) and HEX color measurement tool for 3D printing. Captures true filament color and TD values for HueForge integration to build accurate filament libraries and fix color shifts in multi-color prints. [Details](https://openhardware.directory/devices/biqu-ajax-td1s) | [Markdown](https://openhardware.directory/devices/biqu-ajax-td1s/md) ## Libre Computer Alta Libre Computer Alta (AML-A311D-CC) — Amlogic A311D hexa-core SBC with 4GB LPDDR4, 5 TOPS NPU, Mali-G52 GPU, 4× USB 3.0, Gigabit Ethernet with PoE, and 4K HDR HDMI 2.0 in a Pi-compatible form factor. [Details](https://openhardware.directory/devices/libre-computer-alta) | [Markdown](https://openhardware.directory/devices/libre-computer-alta/md) ## Libre Computer Renegade Elite Libre Computer Renegade Elite (ROC-RK3399-PC) — Rockchip RK3399 SBC with dual Cortex-A72 + quad Cortex-A53, 4GB LPDDR4, M.2 PCIe, DisplayPort 1.2, HDMI 2.0, and UEFI BIOS in a 120×72mm form factor. [Details](https://openhardware.directory/devices/libre-computer-renegade-elite) | [Markdown](https://openhardware.directory/devices/libre-computer-renegade-elite/md) ## Libre Computer Solitude Libre Computer Solitude (AML-S905D3-CC) — Amlogic S905D3 quad-core Cortex-A55 SBC with 2/4GB LPDDR4, 1.2 TOPS NPU, 4× USB 3.0, Gigabit Ethernet with PoE, and 4K HDR HDMI 2.0 in a Pi-compatible layout. [Details](https://openhardware.directory/devices/libre-computer-solitude) | [Markdown](https://openhardware.directory/devices/libre-computer-solitude/md)