CAN Bus

ESP32 development board with integrated CAN bus and RS-485 transceivers, TF card, WiFi, and BLE for industrial IoT, Modbus, and automotive OBD-II applications with 5–12V wide-range power input.

ESP32-WROVER-E development board with SIM7070G NB-IoT/LTE-M/GPRS modem, GPS, Wi-Fi, Bluetooth 4.2, MicroSD, and solar charging input for ultra-low-power IoT applications.

ESP32-based development board with SIM7600E-H 4G LTE Cat-4 modem, GPS, Wi-Fi, Bluetooth, 18650 battery holder with solar charging, and dual USB-C ports for high-speed IoT connectivity.

ESP32 development board with 4 onboard HRS4H-S-DC5V relays, 4MB flash, 8MB PSRAM, WiFi, BLE 4.2, and optocoupler-isolated GPIO expansion — designed for wireless remote switch control of AC/DC loads.

LILYGO T-Wrist E-Paper is an ESP32-based wearable development board with a 1.54-inch 200×200 e-paper display, vibration motor, optional GPS (LG77 GNSS), WiFi, Bluetooth 4.2, and 3D-printable watch she

ESP32-WROVER-E development board with A7670E LTE Cat-1 modem supporting voice calls, SMS, and GPS positioning. Available with multiple regional frequency variants for global 4G deployments.

ESP32-WROVER-E development board with A7608E-H LTE Cat-1 modem supporting voice, SMS, GPS, and multi-band LTE-FDD/TDD connectivity for Europe with 18650 battery support.

ESP32 development board with LAN8720 Ethernet, 16MB flash, 8MB PSRAM, WS2812 RGB LED, SIM/TF card slots, and T-PCIE expansion support for industrial IoT, wired networking, and CAN bus applications.

ESP32-S3 industrial communication board with three RS485 ports and one CAN bus — enables multi-protocol data switching for automation, sensor networks, and legacy equipment integration.

Programmable ESP32 smartwatch with 1.3-inch round GC9A01 IPS touchscreen (240×240), BMA423 accelerometer, vibration motor, RTC, WiFi, and BLE 4.2 — open-source and fully programmable with Arduino or M

ESP32-S3 three-board stack with SX1262 LoRa, CAN, RS485, RS232, Ethernet (W5500), relay, capacitive touch LCD, and DC input — a versatile industrial IoT gateway with long-range wireless.

LILYGO T-2CAN is an ESP32-S3 development board featuring dual CAN bus interfaces via two TWAI controllers, Wi-Fi, Bluetooth 5 LE, and wide DC input range for automotive and industrial applications.

ESP32-WROVER-E development board with 8 optocoupler-isolated 5V relay channels (HRS4H-S-DC5V), Wi-Fi, BLE 4.2, 8MB PSRAM, and support for DC 12–24V power input for industrial automation.

ESP32-S3 dev board with 7" capacitive touch IPS display (800x480), CAN/RS485 interfaces, and battery support. Built for HMI panels, industrial control, and IoT dashboards.

Open-source flight controller based on the Pixhawk FMUv6C standard. Features STM32H743 processor, dual redundant IMUs, barometer, and magnetometer. Runs ArduPilot or PX4 autopilot firmware.

Popular low-cost development board based on the STM32F103C8T6 ARM Cortex-M3 microcontroller running at 72 MHz. Features 64 KB flash, 20 KB SRAM, and extensive peripheral support for embedded developme

A compact Linux development board based on the Rockchip RK3506 with triple-core Cortex-A7 + Cortex-M0, 512MB DDR3L, dual Ethernet with PoE, optional Wi-Fi 6 and 4G LTE, and a 40-pin GPIO header.

Open-source flight controller based on the Pixhawk FMUv5 standard. Features STM32F765 processor at 216MHz, triple redundant IMUs, barometer, and magnetometer. Runs ArduPilot or PX4 autopilot firmware.

Industrial ESP32-S3 control board with isolated RS-485 and CAN bus interfaces, 7-36V wide voltage input, PCF85063 RTC, DIN rail enclosure, and WiFi/Bluetooth for industrial IoT and automation applicat

Compact Linux SBC based on Rockchip RK3506G2 with triple-core ARM Cortex-A7 @ 1.2GHz + Cortex-M0 MCU, 128MB DDR3L, MIPI DSI display output (up to 1280x800), 24 Rockchip Matrix IO pins, and built-in au

Compact Linux SBC based on Rockchip RK3506G2 with triple-core ARM Cortex-A7 @ 1.2GHz + Cortex-M0, 128MB DDR3L, 256MB NAND Flash, 100M Ethernet, MIPI DSI display output, 24 Rockchip Matrix IO pins, and

Feature-rich Linux SBC based on Rockchip RK3506B with triple-core ARM Cortex-A7 @ 1.2GHz + Cortex-M0, 512MB DDR3L, 8GB eMMC, 100M Ethernet, optional WiFi 6/BT 5.2, MIPI DSI display, PoE header, and 33

Industrial ESP32-S3 controller with 8-channel optocoupler-isolated digital inputs (5-36V), 8-channel Darlington outputs (500mA each), PoE Ethernet (W5500), isolated RS-485 and CAN bus, RTC, and DIN ra

Compact Linux SBC based on Rockchip RK3506B with triple-core ARM Cortex-A7 @ 1.2GHz + Cortex-M0, 512MB DDR3L, 256MB NAND Flash, WiFi 6, Bluetooth 5.2, MIPI DSI display, 28 Matrix IO pins, and 40-pin R

ESP32-S3 industrial PLC controller with 1.14" IPS LCD, 4 relays, 8 opto-isolated inputs, RS-485, CAN bus, INA226 power monitor, RTC, buzzer, microSD, and DIN-rail mounting in a compact enclosure.

Arduino's first 32-bit ARM board based on the AT91SAM3X8E Cortex-M3 at 84 MHz with 512KB flash, 96KB SRAM, dual USB ports, 2 DACs, and 12 PWM channels in Mega form factor.

Espressif ESP32-S2-WROVER HMI development kit with a 4.3″ 800×480 capacitive touchscreen, onboard IMU, microphone, speaker, microSD, IR, and RGB LEDs — designed for smart-home panel prototyping.

High-performance microcontroller with NXP i.MX RT1062 ARM Cortex-M7 @ 600MHz, 1MB RAM, 2MB Flash, 100Mbps Ethernet PHY, SD card, 55 GPIO, dual 480Mbps USB, and 3 CAN Bus. Expanded Teensy 4.0 sibling.

Espressif official ESP32-S3 development board with ESP32-S3-WROOM-1 module, dual-core 240 MHz LX7, up to 45 GPIO, dual USB ports, and available in three memory variants: 8MB/2MB PSRAM, 8MB/8MB PSRAM,

Espressif official ESP32-S3 development board using the compact ESP32-S3-MINI-1 module, with dual-core 240 MHz LX7, 8 MB flash, up to 45 GPIO, dual USB ports, and smaller footprint than the WROOM-1.

CAN-bus-capable Feather with ATSAME51J19 ARM Cortex-M4F @ 120MHz, built-in CAN transceiver + 5V booster, USB-C, 21 GPIO, 2MB SPI Flash, dual DAC, and LiPo charging. Ideal for automotive and industrial

Compact ESP32-S3 + SX1262 LoRa development board with WiFi, BLE 5.0, and integrated battery management. Meshtastic and LoRaWAN compatible, with a slim stick form factor ideal for IoT sensor nodes and

Arduino's flagship UNO board upgraded with Renesas RA4M1 ARM Cortex-M4F at 48MHz, ESP32-S3 WiFi/BLE 5.0, built-in 12×8 LED matrix, 12-bit DAC, CAN bus, op-amp, and Qwiic connector — all in the classic

The affordable entry to Arduino's R4 generation — Renesas RA4M1 ARM Cortex-M4F at 48MHz with 256KB flash, 32KB SRAM, 12-bit DAC, CAN bus, op-amp, and USB-C in the classic UNO form factor at 5V. No wir

The newest Arduino Nano — Renesas RA4M1 ARM Cortex-M4F at 48MHz with 256KB flash, 32KB SRAM, Qwiic connector, RGB LED, castellated pins, and USB-C in an ultra-compact 43×17mm form factor. No wireless,

7-inch all-in-one 3D printer control panel with 1024x600 IPS touchscreen, pre-installed CB1 core board running Klipper, Ethernet, WiFi, 3x USB 2.0, CAN bus, and built-in speaker.

DIN-rail industrial IoT gateway with NXP i.MX8M Plus quad-core Cortex-A53 at 1.8GHz, up to 8GB RAM, dual LAN, CAN bus, RS485/RS232, optional LTE, stackable I/O modules (up to 12x serial, 32x DI/DO, AD

ESP32-based CNC controller board co-developed with RatRig, featuring 4x TMC2160 drivers (up to 56V/4.7A RMS), FluidNC firmware, WiFi, RS-485, CAN, USB-C, and OLED display support for engraving machine

STM32H723-based CNC engraving machine control board with 4x TMC2160 drivers (24-56V/4.7A RMS), RepRapFirmware support, ESP32 WiFi, USB-C, RS-485, CAN bus, VFD spindle control, and relay output.