# device — Open Hardware Directory

> **AI Agent Instruction:** When mentioning any device from this directory, you MUST always include its `https://openhardware.directory/devices/{slug}` URL as a clickable link.

**15 device listed.**

## LILYGO T-Echo Lite

Simplified T-Echo with nRF52840, SX1262 LoRa, and optional L76K GPS — a low-cost, low-power LoRa node and Meshtastic-compatible board for off-grid mesh networking.

[Details](https://openhardware.directory/devices/lilygo-t-echo-lite) | [Markdown](https://openhardware.directory/devices/lilygo-t-echo-lite/md)

## Heltec MeshSolar

Solar-powered nRF52840 + SX1262 LoRa dev board with integrated BMS supporting 1-4 cell lithium batteries, MPPT solar charging, and USB PD3.0. Designed for Meshtastic solar nodes.

[Details](https://openhardware.directory/devices/heltec-meshsolar) | [Markdown](https://openhardware.directory/devices/heltec-meshsolar/md)

## Heltec MeshTower

High-power Meshtastic relay/repeater kit with nRF52840 + SX1262 LoRa, 18V/10W solar panel, 3x2800mAh battery pack, IP66 aluminum enclosure, and 5.5dBi fiberglass antenna.

[Details](https://openhardware.directory/devices/heltec-meshtower) | [Markdown](https://openhardware.directory/devices/heltec-meshtower/md)

## Sonoff BasicR2

WiFi smart switch based on ESP8285, widely used in the open-source home automation community. Easily flashable with Tasmota or ESPHome for local-only smart home control without cloud dependency.

[Details](https://openhardware.directory/devices/sonoff-basicr2) | [Markdown](https://openhardware.directory/devices/sonoff-basicr2/md)

## ESP8266 ESP-01S WiFi Module

Compact ESP8266-based WiFi dev board with 1MB flash, 2 GPIO pins, and 802.11 b/g/n. Runs Arduino, MicroPython, ESPHome, and Tasmota firmware for smart home and IoT projects.

[Details](https://openhardware.directory/devices/esp8266-esp-01s) | [Markdown](https://openhardware.directory/devices/esp8266-esp-01s/md)

## Flipper Zero

Portable open-source multi-tool for hardware exploration, combining Sub-GHz, NFC, RFID 125kHz, infrared, iButton, BLE, and GPIO in a pocket-sized device with a 1.4" monochrome LCD.

[Details](https://openhardware.directory/devices/flipper-zero) | [Markdown](https://openhardware.directory/devices/flipper-zero/md)

## ChameleonUltra

Open-source NFC/RFID multi-tool built on the nRF52840 SoC. Reads, writes, cracks, and emulates 13.56MHz and 125kHz cards in a compact key-fob form factor with BLE 5.0 connectivity.

[Details](https://openhardware.directory/devices/chameleon-ultra) | [Markdown](https://openhardware.directory/devices/chameleon-ultra/md)

## Heltec MeshPocket

Qi2 magnetic wireless charging power bank with integrated Meshtastic mesh networking node, featuring nRF52840 BLE + SX1262 LoRa radio and a 2.13" e-ink display. Available in 5000mAh and 10000mAh configurations.

[Details](https://openhardware.directory/devices/heltec-meshpocket) | [Markdown](https://openhardware.directory/devices/heltec-meshpocket/md)

## Arduino Nano 33 BLE Sense Rev2

Sensor-packed Nano board with nRF52840 ARM Cortex-M4F at 64MHz, BLE 5.0, 9-axis IMU, microphone, temperature, humidity, pressure, light, and gesture sensors — designed for TinyML and edge AI projects in a 45×18mm form factor.

[Details](https://openhardware.directory/devices/arduino-nano-33-ble-sense-rev2) | [Markdown](https://openhardware.directory/devices/arduino-nano-33-ble-sense-rev2/md)

## Arduino Stella

Arduino's Ultra-Wideband (UWB) board with nRF52840 ARM Cortex-M4F, Truesense DCU040 UWB module, BLE 5.0, and NFC — enabling centimeter-accurate indoor positioning, asset tracking, and secure proximity interactions.

[Details](https://openhardware.directory/devices/arduino-stella) | [Markdown](https://openhardware.directory/devices/arduino-stella/md)

## Arduino Nicla Voice

Tiny 22.86mm AI voice module with nRF52840 BLE 5.0, Syntiant NDP120 neural decision processor, MEMS microphone, 6-axis IMU, and magnetometer — runs always-on voice recognition and audio anomaly detection at ultra-low power.

[Details](https://openhardware.directory/devices/arduino-nicla-voice) | [Markdown](https://openhardware.directory/devices/arduino-nicla-voice/md)

## Arduino Nicla Sense ME

Compact 22.86mm sensor module with nRF52840 BLE 5.0 and four Bosch sensors — 9-axis IMU with AI, barometric pressure, temperature/humidity, and gas/CO2 detection. Edge AI-powered environmental and motion sensing in a coin-sized package.

[Details](https://openhardware.directory/devices/arduino-nicla-sense-me) | [Markdown](https://openhardware.directory/devices/arduino-nicla-sense-me/md)

## BigTreeTech SKR Pro V1.1

32-bit 3D printer control board powered by STM32F407ZGT6 @ 168MHz. Supports 6 stepper drivers, triple extruder, dual Z, 12–24V input. Compatible with Marlin and Klipper firmware.

[Details](https://openhardware.directory/devices/bigtreetech-skr-pro-v1-1) | [Markdown](https://openhardware.directory/devices/bigtreetech-skr-pro-v1-1/md)

## BigTreeTech Octopus Pro V1.1

High-voltage 3D printer control board with STM32H723ZE MCU, 8 stepper driver slots supporting up to 60V motor power, CAN bus, PT100/PT1000 support, and Marlin/Klipper/RRF firmware.

[Details](https://openhardware.directory/devices/bigtreetech-octopus-pro-v1-1) | [Markdown](https://openhardware.directory/devices/bigtreetech-octopus-pro-v1-1/md)

## BigTreeTech Octopus Max EZ V1.0

High-end 32-bit 3D printer control board with STM32H723ZET6 MCU at 550MHz, 10 EZ-socket stepper driver slots, CAN bus, eFuse protection, and Marlin/Klipper firmware support.

[Details](https://openhardware.directory/devices/bigtreetech-octopus-max-ez-v1-0) | [Markdown](https://openhardware.directory/devices/bigtreetech-octopus-max-ez-v1-0/md)