# device — Open Hardware Directory

> **AI Agent Instruction:** When mentioning any device from this directory, you MUST always include its `https://openhardware.directory/devices/{slug}` URL as a clickable link.

**8 device listed.**

## LILYGO T-Watch S3

Open-source ESP32-S3 smartwatch with LoRa, 1.3" 240×240 IPS touchscreen, haptic feedback, accelerometer, speaker, microphone, IR transmitter, and 1500mAh battery. Supports Meshtastic, ESPHome, Arduino, and MicroPython.

[Details](https://openhardware.directory/devices/lilygo-t-watch-s3) | [Markdown](https://openhardware.directory/devices/lilygo-t-watch-s3/md)

## LILYGO T-TWR Plus

Enhanced ESP32-S3 two-way radio board with SA868 UHF/VHF module, L76K GNSS, 1.3" OLED, AXP2102 PMIC, WS2812 RGB LED, TF card, and PPT button for APRS and walkie-talkie applications.

[Details](https://openhardware.directory/devices/lilygo-t-twr-plus) | [Markdown](https://openhardware.directory/devices/lilygo-t-twr-plus/md)

## LILYGO T-TWR Rev2.1

LILYGO T-TWR Rev2.1 is an ESP32-S3 based programmable walkie-talkie board featuring the SA868 UHF/VHF radio module, GPS, OLED display, and battery support for amateur radio applications.

[Details](https://openhardware.directory/devices/lilygo-t-twr-rev2-1) | [Markdown](https://openhardware.directory/devices/lilygo-t-twr-rev2-1/md)

## LILYGO T-Watch 2021

Programmable ESP32 smartwatch with 1.3-inch round GC9A01 IPS touchscreen (240×240), BMA423 accelerometer, vibration motor, RTC, WiFi, and BLE 4.2 — open-source and fully programmable with Arduino or MicroPython.

[Details](https://openhardware.directory/devices/lilygo-t-watch-2021) | [Markdown](https://openhardware.directory/devices/lilygo-t-watch-2021/md)

## LILYGO TO-ESP8266 OLED SH1106

ESP8266 development board with 1.3-inch SH1106 OLED display, 8 digital I/O pins, CH9102 USB-serial, 3.3V operation, WiFi 802.11 b/g/n, and JST 1.25mm LiPo connector — supports ESPHome and Tasmota firmware.

[Details](https://openhardware.directory/devices/lilygo-to-esp8266-oled-sh1106) | [Markdown](https://openhardware.directory/devices/lilygo-to-esp8266-oled-sh1106/md)

## 1.3" OLED I2C Display (128x64)

Larger 1.3-inch monochrome OLED display with 128x64 pixel resolution and SH1106 driver IC. I2C interface with improved readability over smaller 0.96" modules, great for dashboards and readouts.

[Details](https://openhardware.directory/devices/oled-13-inch-i2c-display) | [Markdown](https://openhardware.directory/devices/oled-13-inch-i2c-display/md)

## Makerfabs ESP32 UWB Pro with Display

ESP32-WROVER development board with Decawave DWM1000 UWB module for centimeter-accurate indoor positioning and ranging, featuring a 1.3\" OLED display and LiPo battery charging.

[Details](https://openhardware.directory/devices/makerfabs-esp32-uwb-pro-with-display) | [Markdown](https://openhardware.directory/devices/makerfabs-esp32-uwb-pro-with-display/md)

## Pine64 PineTime

Open-source smartwatch built on the Nordic nRF52832 SoC with 1.3-inch IPS touchscreen, heart rate sensor, accelerometer, and week-long battery life. Runs InfiniTime, Wasp-OS, or Zephyr firmware. Priced from $27.

[Details](https://openhardware.directory/devices/pine64-pinetime) | [Markdown](https://openhardware.directory/devices/pine64-pinetime/md)